Generator Set Information Menu | Kohler 8/10/12RESVL guide

3.12Generator Set Information Menu

The generator set model number and serial numbers are displayed. No changes are allowed from this menu.

Model and serial numbers are factory set and should not require changes in the field, except in the event that the controller is being replaced. A personal computer running Kohler SiteTech software is required to enter the generator set model number and serial numbers on a replacement controller. Contact an authorized Kohler distributor/dealer for service.

Genset ---->	Genset M/N:
Information	20RESV
	Genset S/N:
	########
	Controller S/N:
	########
	<---- Return
	tp6804
Figure 3-13Generator Set Information Menu

3.13 Genset Run Time Menu

The data shown in Figure 3-14 are displayed. No changes are allowed from this menu.

Eng Runtime displays the total number of hours that the generator set engine has run. The runtime is not resettable.

The Next Maintenance menu shows the number of hours of generator set operation until maintenance is required. The estimated date for the next scheduled maintenance is also displayed. The maintenance reminder intervals are based on the engine manufacturer’s recommendation for changing the oil. Refer to Section 5, Scheduled Maintenance, for maintenance instructions.

After changing the oil and performing other recommended maintenance, go to the Overview menu to reset the maintenance timer. See Section 5.2.5 for instructions to reset the maintenance timer.

Genset ---->	Eng Runtime:
Run Time	12345.6 h
	Eng Starts:
	123456
	Next Maintenance:
	150 h or Mar2012
	<---- Return
Note: Sample data shown.		tp6810
Note: Sample data shown.
Figure 3-14Generator Set Run Time Menu

TP-6880 10/14

Section 3 RDC2 Controller Operation 39

Image 39

Kohler 8/10/12RESVL manual Generator Set Information Menu, Genset Run Time Menu

Contents

TP-6880 10/14a RDC2 Controller Identification Accessory Number Accessory DescriptionProduct Identification Information Generator Set Identification Numbers Table of Contents Scheduled Maintenance TroubleshootingDC2 Controller Operation Accidental starting Can cause severe injury or death Safety Precautions and InstructionsBattery Accidental Starting Fire Can cause severe injury or death Engine Backfire/Flash FireExhaust System Carbon monoxide Can Cause Hazardous voltage Will cause severe injury or death Fuel System Hazardous Noise Hot Parts Heavy Equipment List of Related Literature Transfer Switch LiteratureAccessory Literature Introduction Emission Compliance Period NameplateEmission Information Generator Set Application Service Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Load Control Module LCM AccessoriesCarburetor Heater Programmable Interface Module PIM 1214 Service Views 3Service View Generator Set Operation Prestart Checklist Generator Set Operation TP-6880 10/14 Generator Set Operation Exercising the Generator Set Exercise Automatic Operation with Other Transfer SwitchesSetting the Exerciser Unloaded Cycle Exercise with Complete System Diagnostics Loaded Full-Speed Exercise with RXT only Power Failure During Exercise CycleSystem Diagnostics Unloaded Full-Speed Exercise Shutdowns FaultsATS Communication Errors Resetting the Controller after a Fault Shutdown Fault Message Shutdown SD Condition Check Fault Shutdown SD Condition Check 3Controller Fault Messages Generator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Generator Set/ Transfer Switch Controller Controls and IndicatorsRDC2 Controller Operation LED Operation Controller Keypad LED IndicatorsButton Button Function Active Alert LCD Display Procedure to Change Settings Controller PowerBattery Charging Changing Settings 7Changing Settings Changing Settings on the RDC2 Controller Procedure to Set the Exerciser Setting the ExerciserSetting the Exerciser at Controller Power-up Changing the Exercise Settings 8Procedure to Set the Exerciser on the RDC2 Controller Main Menu RDC2 Controller Menus Engine Metering Menu Overview Menu Voltage Calibration Generator Metering Menu Genset Run Time Menu Generator Set Information Menu Voltage Regulator VR Voltage Adj Setting the ExerciserAdjusting the Display Contrast Genset System Menu Screens on this page do not appear ATS Status Menu Changing ATS Configuration Settings ATS Configuration Menu Networking Information Menus Date and Time Menu Dhcp Networking Status Submenu Networking Configuration Submenu OnCue Plus Password PasswordDhcp Submenu 21Network Configuration Submenu 22RBUS Information Submenu Rbus Information From Figure Remote Devices Submenu Programmable Interface Module PIM Status Menu 25Load Control Module LCM or Load Shed Kit Status Menu Load Control Module LCM or Load Shed Kit Menus Event Log Procedure to View Event History RDC2 Controller Operation TP-6880 10/14 DC2 Controller Operation DC2 Generator Set/ Transfer Switch Controller Description Controller KeypadButton Button Function LED Indication 5Status Displays, Generator Running Exercise Modes Exerciser Reset OnCue Plus Password Maintenance Timer DC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Low Oil Pressure Shutdown Oil Change ProcedureLubrication System Engine Oil Recommendation Fill with oil Reset the maintenance timer on the controllerDrain the oil Replace the oil filter Model Resvl DC2 Resetting the Maintenance TimerSpark Plugs Model Resv RDC2 Air Cleaner Service Air Cleaner, 8RESV/RESVL ModelsPaper Element Service Cooling System Air Cleaner, 10/12RESV/RESVL Models Hazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 USB Port TroubleshootingFault Messages Introduction Problem Possible Cause Corrective Action Troubleshooting Ansi Appendix a Abbreviations LCB Page TP-6880 10/14