Kohler 8/10/12RESVL manual

Genset ---->

System

System Freq:

XX.X Hz

System Phase

System Volt

Battery V:

HOLD:

Next Exercise * HR:MN PM MM/DD/YY

Next Exercise

HR:MN PM MM/DD/YY

HOLD:

Exercise Mode: Loaded

Exercise Mode:

Unloaded Cycle/Unloaded Full/ Loaded Full

HOLD:

Exercise Freq: Weekly

Exercise Freq:

Weekly/Bi-Weekly

Language:

Contrast:

50

<---- Return

tp6804

* If the exerciser has not been set, No Exercise Sch will be displayed.

Figure 3-8Procedure to Set the Exerciser on the RDC2 Controller

TP-6880 10/14

Section 3 RDC2 Controller Operation 35

Image 35

Kohler 8/10/12RESVL manual 8Procedure to Set the Exerciser on the RDC2 Controller

Contents

TP-6880 10/14a RDC2 Controller Identification Accessory Number Accessory DescriptionProduct Identification Information Generator Set Identification Numbers Table of Contents DC2 Controller Operation Scheduled MaintenanceTroubleshooting Accidental starting Can cause severe injury or death Safety Precautions and InstructionsBattery Accidental Starting Fire Can cause severe injury or death Engine Backfire/Flash FireExhaust System Carbon monoxide Can Cause Hazardous voltage Will cause severe injury or death Fuel System Hazardous Noise Hot Parts Heavy Equipment List of Related Literature Transfer Switch LiteratureAccessory Literature Introduction Emission Compliance Period NameplateEmission Information Generator Set Application Service Assistance Service Assistance TP-6880 10/14 Descriptions and Service Views RDC2 Controller Features DC2 Controller Features Load Control Module LCM AccessoriesCarburetor Heater Programmable Interface Module PIM 1214 Service Views 3Service View Generator Set Operation Prestart Checklist Generator Set Operation TP-6880 10/14 Generator Set Operation Exercising the Generator Set Exercise Automatic Operation with Other Transfer SwitchesSetting the Exerciser Unloaded Cycle Exercise with Complete System Diagnostics Loaded Full-Speed Exercise with RXT only Power Failure During Exercise CycleSystem Diagnostics Unloaded Full-Speed Exercise Shutdowns FaultsATS Communication Errors Resetting the Controller after a Fault Shutdown Fault Message Shutdown SD Condition Check Fault Shutdown SD Condition Check 3Controller Fault Messages Generator Enclosure Thermostat Generator Set Operation TP-6880 10/14 RDC2 Controller Operation RDC2 Generator Set/ Transfer Switch ControllerControls and Indicators LED Operation Controller Keypad LED IndicatorsButton Button Function Active Alert LCD Display Procedure to Change Settings Controller PowerBattery Charging Changing Settings 7Changing Settings Changing Settings on the RDC2 Controller Procedure to Set the Exerciser Setting the ExerciserSetting the Exerciser at Controller Power-up Changing the Exercise Settings 8Procedure to Set the Exerciser on the RDC2 Controller Main Menu RDC2 Controller Menus Engine Metering Menu Overview Menu Voltage Calibration Generator Metering Menu Genset Run Time Menu Generator Set Information Menu Voltage Regulator VR Voltage Adj Setting the ExerciserAdjusting the Display Contrast Genset System Menu Screens on this page do not appear ATS Status Menu Changing ATS Configuration Settings ATS Configuration Menu Networking Information Menus Date and Time Menu Dhcp Networking Status Submenu Dhcp Submenu Networking Configuration Submenu OnCue Plus PasswordPassword 21Network Configuration Submenu 22RBUS Information Submenu Rbus Information From Figure Remote Devices Submenu Programmable Interface Module PIM Status Menu 25Load Control Module LCM or Load Shed Kit Status Menu Load Control Module LCM or Load Shed Kit Menus Event Log Procedure to View Event History RDC2 Controller Operation TP-6880 10/14 DC2 Controller Operation DC2 Generator Set/ Transfer Switch Controller Description Controller KeypadButton Button Function LED Indication 5Status Displays, Generator Running Exercise Modes Exerciser Reset OnCue Plus Password Maintenance Timer DC2 Controller Operation TP-6880 10/14 Scheduled Maintenance Scheduled Maintenance Service Schedule Low Oil Pressure Shutdown Oil Change ProcedureLubrication System Engine Oil Recommendation Fill with oil Reset the maintenance timer on the controllerDrain the oil Replace the oil filter Model Resvl DC2 Resetting the Maintenance TimerSpark Plugs Model Resv RDC2 Paper Element Service Air Cleaner ServiceAir Cleaner, 8RESV/RESVL Models Cooling System Air Cleaner, 10/12RESV/RESVL Models Hazardous noise Can cause hearing loss EZ-273000-J Storage Procedure Scheduled Maintenance TP-6880 10/14 USB Port TroubleshootingFault Messages Introduction Problem Possible Cause Corrective Action Troubleshooting Ansi Appendix a Abbreviations LCB Page TP-6880 10/14