Troubleshooting, Indication Procedure Reference | Kyocera copier

Section 8 TROUBLESHOOTING

If one of the following indications is displayed

When any of the following indications appears on the copy quantity/magnification display, perform the corresponding procedure.

	Indication	Procedure	Reference
	Indication	Procedure	Page
			Page


	“E07” appears on the copy quantity/	The size of paper registered in the default settings is different than the	3-1
	magnification display	size of the paper actually used. Check the paper size.
		Pull out the corresponding drawer and then push it back in to delete the
		error indications.

	“E11” appears on the copy quantity/	The Paper Feeder was selected, but the upper drawer is not installed or is	—
	magnification display	not inserted properly.
		Push the upper drawer securely into the copier.

	“E12” appears on the copy quantity/	When printing out a list or report, there was no 8 1/2" × 11" or A4 size	—
	magnification display	paper available.
		Press the Paper Select key to select the source of paper feed and then
		press the Start key. Print out will be performed onto paper from the
		selected location.

	“E31” appears on the copy quantity/	The amount of waste toner in the copier has reach the acceptable limit.	—
	magnification display	Contact your service representative or an authorized service center.

	“E32” appears on the copy quantity/	The toner container is not installed in the copier.	9-2
	magnification display	Install the toner container.

	“E70” appears on the copy quantity/	If the optional Document Processor is installed on your copier, there are	—
	magnification display	originals remaining on the original table.
		Remove the originals, reset them on the original table and try to copy
		again.

	“E71” appears on the copy quantity/	The copier will attempt to make copies from any originals that remain	—
	magnification display	uncopied.
		Reset all of the originals on the original table and try to copy again.

8-1

Image 67

Kyocera copier manual Troubleshooting, If one of the following indications is displayed, Indication Procedure Reference

Contents

1500 Page IMPORTANT! Please Read First Copy Default SettingsTroubleshooting Maintenance and Operation Information Contents Iii Preset Zoom mode Image quality selectionEco-Copy mode See 200% Paper Recycling Low Power ModeOff Mode About the International Energy Star Program Symbols Page Label IMPORTANT! Please Read First Other precautions Installation Precautions Precautions for USE Other precautions Cdrh Act Safety of laser beamMaintenance Safety switchPage Limited Warranty for NEW Copier Model Page Main Body Names of Parts Stopper extension lock DrawerPaper width guides Paper stopper Right cover anchor pin Power switchPower cord Document Processor connector Face-up tray Operation panel Auto Clear function Auto Drawer Switching function Names of Parts Loading paper PreparationsLoading paper into a drawer Preparations Preparations Selecting the paper size Code number Size Setting paper on the multi-bypass trayInch Specification Metric Specification A4 A6R, and Folio Preparations XXX Selecting the paper size standard setting Selecting the paper size temporary setting Thick Paper mode Attaching the face-up tray Basic Operation Basic copying procedure Start copying Adjusting the copy exposureSetting the number of copies to be made Setting an original At the end of copying Making enlarged and reduced copies Zoom mode50% Preset Zoom mode Low Power mode More about the Off mode Off mode Basic Operation In-1 Metric specificationCopy Functions Layout modes Copy Functions When setting the originals on the platen When setting the originals in the Document Processor Press the 2in1/4in1 key until the 2in1 indicator lights Press the 2in1/4in1 key until the 4in1 indicator lights Selecting the borderline Code number Borderline types Selecting the order of 4-in-1 layout Copy Functions Original Copy Press the Sort key to light the Sort indicator Sort mode Program function Using programmed settings to make copiesRegistering the program Available default items Copy Default SettingsDefault Description Available settings Reference Number Copy Default Settings Non-Standard Size Paper Width and it Mode ON/OFF Copy Default Settings Accessing and changing the default settings Sample User Copy Setting List Copy Default Settings Copy Default Settings Copy Default Settings Copy Default Settings Checking the total copy count and printing out a report Names of parts Optional EquipmentDocument Processor Acceptable originals Optional Equipment Setting originals in the Document Processor Setting originals on the platen Additional Memory Paper Feeder Indication Procedure Reference TroubleshootingIf one of the following indications is displayed Troubleshooting If paper jams Misfeed location indicators Paper jam inside the copier Removal procedures Paper jam in a drawer Paper jam in the paper eject section Original jam in the optional Document Processor Paper jam in the multi-bypass tray Troubleshooting If other trouble occurs Trouble Checkpoint Procedure Reference Troubleshooting Cleaning the copier Maintenance and Operation Information Replacing the toner container Maintenance and Operation Information Cleaner Home Position Cleaning the charger and the registration roller Close the front cover Close the upper front cover Main Body Specifications Paper Feeder option Document Processor optionAdditional Memory option Duplex 2-sided copying Environmental SpecificationsPaper feed Additional Memory Paper Feeder Document Processor Optional equipmentAvailable options Document Processor Function selected first Function selected second Appendix Functions and settings combination chart Numerics Index Toner Coverage Report default setting Total copy count Memo Page Page 2003