Using the Access Point’s SecureEasySetup Feature | Linksys WAP54G

Wireless-G Access Point

Using the Access Point’s SecureEasySetup Feature

Read these instructions before you press any SecureEasySetup buttons. You should locate the SecureEasySetup buttons of your devices before using the Access Point’s SecureEasySetup feature.

NOTE: SecureEasySetup uses WPA-Personal encryption. If your current wireless devices do not support WPA-Personal security, then you cannot use SecureEasySetup on your network. You will need to manually configure your network security using the encryption supported by your existing devices.

1.Before you push any button, locate the SecureEasySetup button for each of your other SecureEasySetup devices. If you are not sure where to find this button, click Where is my other SecureEasySetup button?

You will see a screen showing the SecureEasySetup logo. Click the Next button to continue or the Close button to return to the Configure Wireless Settings screen.

You will see a screen with instructions on how to locate the SecureEasySetup hardware button. If your device does not have a hardware button, it most likely will have a software button. Click the Next button for instructions to locate the software button, or click the Close button to return to the Configure Wireless Settings screen.

You will see a screen with instructions on how to locate the SecureEasySetup software button. Click the Close button to return to the Configure Wireless Settings screen.

Chapter 5: Setting up the Wireless-G Access Point

Figure 5-10: SecureEasySetup Screen

Figure 5-11: SecureEasySetup Logo

Figure 5-12: Additional Information - Hardware Button

Figure 5-13: Additional Information - Software Button

14

Using the Setup Wizard

Image 21

Linksys WAP54G manual Using the Access Point’s SecureEasySetup Feature, SecureEasySetup Screen

Contents

802 GHz .11g Wireless- G Copyright and Trademarks How to Use this User Guide Table of Contents Appendix a Troubleshooting Appendix B Wireless SecurityFrequently Asked Questions Back Panel Front Panel 25 Congratulations Screen Site Survey Screen Welcome Introduction What’s in this User Guide? Wireless-G Access Point Planning Your Wireless Network Network TopologyRoaming Network Layout Cisco logo Getting to Know the Wireless-G Access Point Back Panel LAN Port Connecting the Wireless-G Access Point Connections for SetupOverview Using the Setup Wizard Setting up the Wireless-G Access Point Connect the Network Cable to the Router or Switch Screen Check the Access Point’s Status Screen Password Screen Basic Settings Screen 10 SecureEasySetup Screen Using the Access Point’s SecureEasySetup Feature 15 Confirm New Settings Screen 16 Congratulations Screen Configuring a Non-SecureEasySetup Device 17 Configure Wireless Settings Screen Manually Configuring the Access Point’s Wireless Settings WEP 128-Bit WEP 64-Bit WPA2 Personal WPA Personal WPA2 Mixed Mode Linksys Wireless GuardWPA Enterprise 25 Congratulations Screen 26 Attention Screen Configuring the Linksys Wireless Guard Settings 28 Securing Your Access Point Screen 31 Wireless Guard Congratulations Screen Client Software Installation Using the Linksys Wireless Guard Service Exit Other Applications Destination Location Restart Your Computer Network Access Your Account Accessing your Account Add a Guest 11 Network Administration 12 Modify Access Control Member Registration Add a Member 16 Subscriber Information 18 Credentials Information Securing or Unprotecting Your Wireless Guard Network To unprotect a networkTo secure an unprotected network Configuring the Wireless-G Access Point SetupNavigating the Utility Wireless AdministrationStatus Setup Network Setup Tab Accessing the UtilityNetwork Setup Configuration Type Setup Static IP Screen Setup AP Mode Tab AP ModeLAN MAC Address Configuring the Wireless-G Access Point Setup AP Mode Tab Wireless-G Access Point Basic Wireless Settings Wireless Basic Wireless Settings Tab 12 Confirm Reset Wireless Security Wireless Wireless Security TabWPA-Personal WPA2-Personal WPA-Enterprise WPA2-Mixed Radius Wireless Wireless MAC Filter Tab Wireless MAC FilterAccess Restriction Advanced Wireless Wireless Advanced Wireless Settings Tab Wireless-G Access Point AP’s Password Administration Management TabBackup and Restore Management Administration Snmp Tab Snmp V1/V2cSnmp Community Log Administration Log Tab Administration Firmware Upgrade Tab Administration Factory Defaults TabFirmware Upgrade Factory Defaults Status Local Network Tab AP’s InformationLocal Network Wireless Network Status Wireless Network Tab Frequently Asked Questions Appendix a Troubleshooting What Ieee 802.11g features are supported? What is the ISM band? Does the Access Point function as a firewall? Appendix B Wireless Security Security PrecautionsSecurity Threats Facing Wireless Networks Security Threats Facing Wireless Networks Wireless-G Access Point Appendix C Upgrading Firmware Figure C-1 Firmware Upgrade Appendix D Windows Help Shared ResourcesNetwork Neighborhood/My Network Places Appendix E Glossary Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Wireless-G Access Point Appendix F Specifications Operating Humidity Limited Warranty Appendix G Warranty Information FCC Statement Appendix H Regulatory Information Appendix I Contact Information Need to contact Linksys?Information section in this Guide