Marantz SR5005 manual Hdmi Setup

ENGLISH

Setting items	Setting details
Channel Level	Test Tone Start : Output test tone.
Set the volume of the test	• FL / C / FR / SR / SBRz / SBLz / SL / FHL / FHR / SW : Select the
tone to be the same when it	speaker.

is output from each speaker. zz When the “Speaker Config.” – “S.Back” setting (vpage 57) is set to “1sp”, “S.Back” is displayed.

• –12.0dB – +12.0dB (0.0dB) : Adjust the volume.

• When o is pressed while the subwoofer volume is set to “–12 dB”, the “Subwoofer” setting switches to “OFF”.

• When “Channel Level” is adjusted, the adjusted values are set for all the surround modes. To adjust the channel level separately for the different

surround modes, use the operation see page 40.

• When you press TEST TONE on the remote control, you can enter this setting item immediately.

NOTE

• Speakers set to “None” in the “Speaker Config.” (vpage 56) settings are not displayed.

• When a headphones jack is inserted in the PHONES jack of this unit, the

“Channel Level” is not displayed.

Default : The “Channel Level” settings are returned to the default settings.

Manual Setup

Setting items	Setting details
Front Speaker Setup	• A：Front speaker A is used.
Set the front speakers to	• B：Front speaker B is used.
use for every surround	• A+B：Both front speakers A and B are used.
mode.	You can switch speakers by pressing SPKR
	A/B on the remote control.
HDMI Setup	Default settings are underlined.
Make settings for HDMI video/audio output.
Setting items	Setting details
Auto Lip Sync	ON : Compensated.
Make automatic	OFF : Not compensated.
compensation for timing
shift in audio and video
output.
HDMI Audio Out	Amp : Play back through speakers connected to the receiver.
Select HDMI audio output	TV : Play back through TV connected to the receiver.
device.	When the HDMI control function is activated, priority is given to the TV

audio setting (vpage 39 “HDMI control function”).

	• Yes : Reset to the defaults.
	• No : Do not reset to the defaults.
Crossover Freq.	Crossover : Set the crossover frequency.
Set the maximum frequency	• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
of the bass signal output	250Hz
from each channel to	Advanced : Specify crossover frequency for each speaker.
the subwoofer. Set the
	• Front / Center / Surround / S.Back / Front Height : Select the speaker.
Crossover Freq. to suit the
	• 40Hz / 60Hz / 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz /
bass reproduction capability
	250Hz : Set the crossover frequency.
of the speaker being used.

HDMI Control

You can link operations with devices connected to HDMI and compatible with HDMI Control.

ON : Use HDMI control function.

OFF : Do not use HDMI control function.

•When a device that is not compatible with the HDMI control function is connected, set “HDMI Control” to “OFF”.

•Please consult the operating instructions for each connected component to check the settings.

•Refer to “HDMI control function” (vpage 39) for more information about the HDMI control function.

• “Crossover Freq.” can be set when the “Bass Setting” – “Subwoofer

Mode” (vpage 57) setting is “LFE+Main”, or when you have a speaker

that is set to “Small”.

• Always set the crossover frequency to “80Hz”. When using small

speakers, however, we recommend setting the crossover frequency to

a higher frequency.

• For speakers set to “Small”, sound below the crossover frequency

is cut from the sound output. The cut bass sound is output from the

subwoofer or front speakers.

• The speakers that can be set when “Advanced” is selected differ

depending on the “Subwoofer Mode” setting (vpage 57).

• When “LFE” is selected, speakers set to “Small” at “Speaker Config.”

can be set. If the speakers are set to “Large”, “Full Band” is displayed

and the setting cannot be made.

• If set to “LFE+Main”, this setting can be made regardless of the

speaker size.

NOTE

•When “HDMI Control” is set to “ON”, it consumes more standby power. If you are not using this unit for an extended period, it is recommended that you unplug the power cord from the power outlet.

•“HDMI Control” does not work when the power to the equipment is off. Either turn power on or set to standby.

•The HDMI control function controls operations of a TV that is compatible with the HDMI control function. Make sure that the TV and HDMI are connected when you perform HDMI control.

•If the “HDMI Control” settings have been changed, always reset the power to connected devices after the change.

58

Remote control operation	Move the cursor	Confirm the setting	Return to previous menu
buttons	(Up/Down/Left/Right)