LAN Setup,  To change the MTU size | NETGEAR JNR1010V2 instruction

JNR1010v2 N150 Wireless Router

The following table describes common MTU sizes and applications.

Table 3. Common MTU sizes

MTU	Application

1500	The largest Ethernet packet size. This value is the typical setting for non-PPPoE,
	non-VPN connections, and is the default value for NETGEAR routers, adapters, and
	switches.

1492	Used in PPPoE environments.

1472	Maximum size to use for pinging. (Larger packets are fragmented.)

1468	Used in some DHCP environments.

1460	Usable by AOL if you do not have large email attachments, for example.

1436	Used in PPTP environments or with VPN.

1400	Maximum size for AOL DSL.

576	Typical value to connect to dial-up ISPs.

To change the MTU size:

1.Log in to the router.

For more information, see Log In to Your Router After Installation on page 18.

2.Select ADVANCED > Setup > WAN Setup. The WAN Setup screen displays.

3.In the MTU Size field, enter a new size from 64 through 1500.

4.Click the Apply button. Your changes are saved.

LAN Setup

You can configure LAN IP services such as Dynamic Host Configuration Protocol (DHCP) and Routing Information Protocol (RIP).

The router is shipped preconfigured to use private IP addresses on the LAN side and to function as a DHCP server. The router’s default LAN IP configuration includes the following settings:

•LAN IP address. 192.168.1.1

•Subnet mask. 255.255.255.0

These addresses are part of the designated private address range for use in private networks and are suitable for most applications. If your network requires the use of a different IP addressing scheme, change the settings in the LAN Setup screen.

genie ADVANCED Home

46

Image 46

NETGEAR JNR1010V2 user manual LAN Setup,  To change the MTU size, LAN IP address

Contents

JNR1010v2 N150 Wireless Router Compliance SupportTrademarks Contents Administration Appendix a Supplemental Information Hardware Setup Get to know your router Hardware Features Unpack Your Router Front Panel Router front panel has the following status LEDs JNR1010v2 N150 Wireless Router Front panel LED descriptions Back panel has the following ports, button, and connector Back Panel Label Position Your Router To position your router  To prepare your router for installation Cable Your Router Verify the Cabling  To start your network Get Started with Netgear genie Connect to the router Wireless Devices and Security Settings Router Setup PreparationTypes of Logins and Access Use Standard TCP/IP Properties for Dhcp  To use Netgear genie to set up your router Netgear genie SetupBrowse to http//routerlogin.net Log In to Your Router After Installation Upgrade Router Firmware Basic Home Screen Change the Password Select Advanced Administration Set Password  To set up password recovery Password RecoverySelect the Enable Password Recovery check box  To recover your password  To use WPS to join the wireless network Add Wireless Devices or Computers to Your NetworkWi-Fi Protected Setup Method Manual Method Genie Basic Settings Your Internet connection and network  To view or change the Internet setup Internet SetupSelect Basic Internet Internet IP Address Internet IP Address Basic Wireless Settings Select Basic Wireless Genie Basic Settings Genie Basic Settings WPA-PSK and WPA-PSK + WPA2-PSK Mixed Mode Security Options  To configure the WEP security and wireless passphrase WEP Genie Basic Settings  To view the devices that are connected to your networks Attached DevicesSelect Basic Attached Devices Guest Network  To set up a guest networkSelect Basic Guest Network Genie Basic Settings Specify custom settings Genie Advanced Home Setup Wizard  To launch the Setup Wizard Genie Advanced Home WPS Wizard  To use the WPS Wizard Genie Advanced Home  To change the WAN settings WAN SetupSelect Advanced Setup WAN Setup Genie Advanced Home Default DMZ Server  To set up a default DMZ server Change the MTU Size  To change the MTU size LAN SetupLAN IP address  To change the LAN settings Use Router as Dhcp Server Clear the Use Router as Dhcp Server check box Set Up Address Reservation To disable the Dhcp server feature  To reserve an IP address  To edit or delete a reserved address entry Genie Advanced Home Administration Manage your network Manually Update the Router Firmware  To check for new firmware and update your router  To back up the router’s configuration settings Manage the Configuration FileBack Up Settings Select Advanced Administration Backup Settings  To restore configuration settings that you backed up Restore Configuration SettingsDo not interrupt the reboot process Erase Configuration Settings Advanced Settings Enhance the performance of your router Advanced Settings for Your Wireless Network Advanced Wireless Settings To change advanced settings for your wireless network Enable or Disable Wireless Router Radio  To enable or disable the wireless router radio Set Up a Wireless Schedule  To configure and enable the wireless schedule Set Up the WPS Settings  To change the WPS settings for your wireless network Wireless Distribution System Wireless repeating scenario Select Advanced Advanced Setup Wireless Repeating Function Set Up the Base Station To set up the base station Select the Enable Wireless Repeating Function check box Set Up a Repeater Select the Wireless Base Station radio button  To configure the router as a repeater Complete the Repeater IP Address field Select Advanced Advanced Setup Static Routes  To set up a static routeStatic Routes Advanced Settings Universal Plug and Play  To edit or delete a static route  To configure Universal Plug and Play Advanced Settings Monitoring Monitor your router and network traffic Router Status and Usage Information Screen  To display the Router Information pane Router Information PaneInternet Port Pane LAN Port Statistics  To view the traffic statistics  To view the connection status Connection StatusDhcp connection PPPoE connection Pptp connection Guest Network Pane Wireless Settings Pane To display the Wireless Settings pane  To display the Guest Network pane Monitoring Troubleshooting Find and fix problems Quick Tips Wireless SettingsNetwork Settings Sequence to Restart Your Network Power LED Stays Amber Power LED Is Off or BlinkingTroubleshoot with the LEDs Internet or Ethernet Port LEDs Are Off WiFi LED Is OffAll LEDs Remain Lit After Startup WPS Button Blinks Amber Cannot Log In to the Router Troubleshoot Internet Browsing Cannot Access the Internet To check the WAN IP address Troubleshoot a PPPoE Internet Connection  To troubleshoot a PPPoE Internet connection Changes Not Saved Wireless ConnectivityTroubleshoot Your Network Using the Ping Utility Test the LAN Path to Your Router Test the Path from Your Computer to a Remote Device  To ping the router from a computer running Windows Troubleshooting Supplemental Information Additional details Factory Settings JNR1010v2 router factory default settings Technical Specifications JNR1010v2 router specifications