Advanced Operations
En-64
Operating
procedure
(➔page60)
■Speakers Type(Front)
`Normal:
Select this if you’ve connected your front
speakers normally.
`Bi-Amp:
Select this if you’ve bi-amped your front
speakers.
■Powered Zone 2
`No
`Yes:
Zone 2 speakers can be used (Powered Zone 2
enabled).
Note
• If the “Speakers Type(Front)” setting is set to “Bi-Amp”,
Powered Zone 2 cannot be used.
• When the “Powered Zone 2” setting is set to “Yes” and
Zone 2 is turned on, the surround back and front high
speakers cannot be used.
Speaker Configuration
With these settings, you can specify which speakers
are connected and a crossover frequency for each
speaker. Specify “Full Band” for speakers that can
output low frequency bass sounds adequately, for
example, speakers with a good sized woofer. For
smaller speakers, specify a crossover frequency.
Sounds below the crossover frequency will be output
by the subwoofer instead of the speaker. Refer to
your speaker’s manuals to determine the optimum
crossover frequencies. If you set up your speakers
using Audyssey MultEQ Room Correction and
Speaker Setup, please make sure manually that any
THX speakers are set to “80Hz(THX)” crossover.
■Subwoofer
`Yes
`No
■Front
`Full Band
`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
Note
• If the “Subwoofer” setting is set to “No”, the “Front” setting
is fixed at “Full Band”.
■Center*1, Surround*1
`Full Band
`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
`None
■Front Wide*1*2*4, Front High*1*2*3
`Full Band
`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
`None
■Surround Back*1*2*3
`Full Band
`40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
`None
Note
*1 “Full Band” can be selected only when “Full Band” is
selected in the “Front” setting.
*2 If the “Surround” setting is set to “None”, this setting
cannot be selected.
*3 If the “Speakers Type(Front)” setting is set to “Bi-Amp”,
or the “Powered Zone2” setting i s set to “Yes” together
with Zone 2 turned on, this setting cannot be selected.
*4 If the “Speakers Type(Front)” setting is set to “Bi-Amp”,
or the “Powered Zone2” setting i s set to “Yes”, this
setting cannot be selected.
■Surround Back Ch
`1ch:
Select if only one surround back speaker L is
connected.
`2ch:
Select if two (left and right) surround back
speakers are connected.
Note
• If the “Surround Back” setting is set to “None”, this setting
cannot be selected.
■LPF of LFE
(Low-Pass Filter for the LFE Channel)
`80Hz, 90Hz, 100Hz, 120Hz
`Off:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff
frequency of the LFE channel’s low-pass filter
(LPF), which can be used to filter out unwanted
hum. The LPF only applies to sources that use the
LFE channel.
Note
• If you’re using THX-certified speakers, select “80Hz”.
■Subwoofer Phase
`0º
`180º:
Moves the subwoofer phase.
Note
• If the “Subwoofer” setting is set to “No”, this setting cannot
be selected.
This setting is set automatically by
Audyssey MultEQ® Room Correction and Speaker
Setup function (➔page 27).