Panasonic AJ-D960EG manual Direct, Moni SEL, ON1, MON Auto, Audio PB, JOG Proc, Dv Pb Att, Rec Pt

Setup menus

USER menu	<AUDIO> (continued)
		Item		Setting
									Description
	No.	Superimposed	No.		Superimposed
		display				display
	733	CUE OUT	0000			NORMAL			For selecting the output from the CUE OUT connector.
			0001				DIRECT		0: The timing is aligned with the output picture.
									1: Whatever has been recorded on the tape is output with no delay.
									<Note>
									When “1” (DIRECT) has been selected, the timing of the out-
									put picture and that of the cue output are not aligned properly.
									However, this setting is effective only during DVCPRO (25
									Mbps) mode playback.
	734	MONI SEL	0000					OFF	This selects whether the operation of the MONITOR SELECT
		INH	0001					ON	button on the front panel is to be enabled or disabled.
			0002					ON1	0: Operation is enabled.
									1: Operation is disabled.
									2: Operation is disabled in the FULL display mode and
									enabled only in the FINE display mode.
	735	MON AUTO	0000					L/R	Although CUE is automatically output to the monitor output in
		SEL	0001					L	accordance with the operation mode when a setting other
			0002					R	than MANU has been selected by setup menu item No. 721
									(MONI CH SEL), the MON AUTO SEL setup menu item is
									used to select the monitor channel which is to be auto-
									matically switched to CUE.
									0: CUE is output to both the left and right channels.
									1: CUE is output to the left channel only.
									2: CUE is output to the right channel only.
	736	AUDIO PB	0000					DIS	This selects whether the playback level controls are to func-
		VR	0001					ENA	tion in the EE mode when INT SG has been selected as the
									setup menu item No. 700 (INT SG) setting.
									0: The INT SG output level is fixed at UNITY.
									1: The INT SG output level can be varied using the playback
									level controls.
	737	JOG PROC	0000					OFF	Selects the digital audio output slow signal processing in the
			0001					ON	JOG/VAR/SHTL mode.
									0: The sound from the digital audio without the slow signal
									processing is output even in the STILL mode.
									1: The sound from the digital audio output after the slow
									signal processing is output.
	750	DV PB ATT	0000					OFF	This selects the audio output level during DV playback.
			0001					ON	0: The audio output level is not attenuated.
									1: The audio output level is attenuated (reduced).
	751	REC PT	0000					OFF	This selects whether to mute the sound where recordings are
		MUTE	0001					ON	joined during DV/DVCAM playback.
									0: The sound is not muted.	1: The sound is muted.

The underline on the setting item denotes the initial setting.

<Concerning the CUE output in the search mode>

The table below shows how the CUE output to the monitor and main signal system outputs differs according to how the setup menu item (No. 721, No. 731 and No. 735) settings are combined.

731	721	735	Monitor output			Main signal system output
CUE OUT	MONI CH	MON AUTO
			Lch	Rch	CH1	CH2	CH3	CH4
SEL	SEL	SEL
		L/R
	MANU	L	PCM	PCM
OFF		R			PCM	PCM	PCM	PCM
	AUTO1	L/R	CUE	CUE
		L	CUE	PCM
	AUTO21	R	PCM	CUE
		L/R
	MANU	L	PCM	PCM	PCM	PCM	PCM	PCM
ON		R
	AUTO1	L/R	CUE	CUE	CUE	CUE	CUE	CUE
		L	CUE	PCM	CUE	PCM	CUE	PCM
	AUTO21	R	PCM	CUE	PCM	CUE	PCM	CUE

<Notes>

•PCM audio signal output is muted when the VTR is played outside the –1 to +2.0 normal speed.

•When either AUTO1 or AUTO11 is selected, the PCM audio signal is output within –1 to +2.0 normal speed even in the automatic CUE output mode.

82 (E)