Panasonic DMR-EH60 Channel/Clock settings when TV Guide On ScreenTM system is not used, Press

Channel/Clock settings when TV Guide On ScreenTM system is not used

Refer to the control reference on page 54.

Preparation:

If the television program list has already been downloaded, return the unit to the factory preset condition using the steps indicated below.

When the unit is on and stopped

1Press and hold [X CH] and [W CH] on the main unit for about five seconds.

The unit turns off.

2Press [Í DVD POWER] to turn the unit on.

3Complete the TV Guide On ScreenTM system setup (until [ENTER] is pressed after the “Watch TV” message screen is displayed).

XCH W

HDD DVD SD

OPEN/CLOSE	DRIVE	REC
	SELECT
C H		/x1.3

S VIDEO	VIDEO	L/MONO-AUDIO-R
DV I N		I N 2

[Note]

You can set scheduled recording only manually after you set the unit with “Set Channels Automatically”.

Auto channel/clock settings

1 Press [SETUP].

2 Press [3, 4] to select “Channel” and press [1].

3 Press [3, 4] to select “Set Channels

Automatically” and press [ENTER].

4 Press [2, 1] to select “Yes” and press [ENTER].

5 Press [ENTER].

Auto Channel Setting starts. This takes a few minutes.

The unit then proceeds with Auto Clock Setting. The time is displayed when finished.

	SETUP
		Set Clock Automatically
	Channel	Auto Clock Setting is complete.
	Setup
			4/4/2005 12:15 AM
	Disc
			DST.............. On
	Video		Time Zone..... CST
	Audio
≥DST, Daylight		Saving Time, shows the			summertime setting.
≥TIME ZONE		shows the time difference			from Greenwich
	Mean Time (GMT).
	EST (Eastern Standard Time)			l GMT j5
	CST (Central Standard Time)			l GMT j6
	MST (Mountain Standard Time) l GMT j7
	PST (Pacific Standard Time)			l GMT j8
	AST (Alaska Standard Time)			l GMT j9
	HST (Hawaii Standard Time)			l GMT j10

For other areas: xx hr

≥If the Auto Clock Setting does not start automatically, select “Clock Settings” from the “Setup” tab and then select “Set Clock Automatically”.

≥If the time was not set correctly, use manual clock setting (➡ 17) or adjust time zone.

6 Press [ENTER].

≥The unit configures channels according to the Signal Source (RF IN) settings as follows.

Signal Source	Band	Channel
(RF IN)
Antenna	VHF	2–13
	UHF	14–69
	VHF	2–13
	CATV LOW BAND	95–99
	CATV MID/SUPER BAND	14–36
CableTV
	CATV HYPER BAND	37–65
	ULTRA BAND	66–94
		100–125
	SPECIAL CATV CHANNEL	1

Adjust Time Zone

Adjust the time zone (j1 or i1) if it was not set correctly with auto clock setting.

You cannot change this setting if you set the clock manually.

1 Press [SETUP].

2 Press [3, 4] to select “Setup” and press [1].

3 Press [3, 4] to select “Clock

Settings” and press [ENTER].

4 Press [3, 4] to select “Adjust Time

Zone” and press [ENTER].

	SETUP
			Adjust Time Zone
			j1
	Channel		0
	Setup
			i1
	Disc
	Video
5 Press [3		, 4] to select “s1” or “r1”
and press		[ENTER].

Convenient functions

To return to the previous screen

Press [RETURN].

To exit the screen

Press [SETUP].

To cancel partway while Auto Channel/Clock Setting is taking place

Press [RETURN].

To set so the television program list is not displayed automatically when you turn the unit on RQT8307

➡ 29, “Review Options” menu–Selecting the TV Guide On ScreenTM system start up pattern

57