Connection, Before starting connection | Panasonic PT-D7600U

Connection

Before starting connection

Before connection, read carefully the instruction manual for the device to be connected.

Turning off the power switch of the devices before connecting cables.

If any connection cable is not supplied with the device, or if no optional cable is available for connection of the device, prepare a necessary system connection cable to suit the device.

Video signals containing too much jitter may cause the images on the screen to randomly wobble or wafture. In this case, a time base

The pin-out and signal names of the S-VIDEO IN terminal are shown in the diagram below.

	Pin No.	Signal
		Ground
		(luminance signal)
		Ground (color signal)
	Outside view	Luminance signal
	Outside view	Color signal
		Color signal

The pin-out and signal names of the RGB2 input terminal are shown in the diagram below.

corrector (TBC) must be connected.

The projector accepts the following signals: video, S-Video, analog RGB and digital signals from the PC.

Some PC models cannot be connected to the projector.

Outside view

Pin No.

Signal

R/PR

G/G · SYNC/Y

PB

SDA

HD/SYNC

VD

SCL

and	are not assigned.
~ ,	and are GND terminals.
and	are effective if the PC has the corresponding
functions.

24

Image 24

Panasonic PT-D7600U operating instructions Connection, Before starting connection, · Sync/Y Sda Hd/Sync Scl

Contents

Commercial Use Model No. PT-D7500U Dear Panasonic Customer Model number PT-D7500U / PT-D7600USerial number Page Contents Precautions with regard to safety Insulate the battery using tape or similar before disposal Use only the Specified batteryDo not place liquid containers on top of the projector Do not insert any foreign objects into the projector Accessories Do not look into the lens while the projector is being usedDo not use the old lamp unit Lamp section may break Precautions on handling Examples of system expansion Remote control When the operation mode selector is set to ProjectorName and function of parts When the operation mode selector is set to Computer Name and function of parts Front and side of the projector Rear view of the main unit Controls on rear panel Video in terminal Video OUT terminalRGB YPBPR2 input/RGB YPBPR1 output terminal pages 26 REMOTE2 terminal Using the remote control unit Effective range of remote control operationLoading dry cells Setting projector ID number to remote control Using the remote control unitProcedure of ID setting Using the remote control as a PC mouse Using a wired remote controlOperation mode selector switch Installation Adjusting the leveling feetProjection scheme Installation geometry Projection distance SH Effective screen height Size EffectiveInch Installation Screen dimensions Projection distance L Zoom lensFor the screen aspect ratio Units m feet/inches WidthSW Minimum Maximum ET-D75LE2/SC 2.0-3.0 ET-D75LE1 ET-D75LE1SCET-D75LE2 ET-D75LE2SC Connection Before starting connection· SYNC/Y SDA HD/SYNC SCL Example of connecting with Video devices Video deck TBC built-in Color monitor Control PCVideo deck TBC built-in High-vision video deck Example of connecting with personal computers ConnectionControl PC PC or color monitor With RGB input terminals Example of connecting with the signal selector Color monitor with RGB input terminal Installation of input module optional Installing the input moduleTypes of the input modules optional Procedure of installation Register the input signalRemove the slot cover Insert the input module Connecting signals to the input module Installation of input module optional Connecting the signal to the analog RGB signal input module Connecting the component signalsRGB signal input module optional SUB BNC Connecting the signal to the video signal input module Connecting the video signalsVideo signal input module optional BNC Connecting the component signals Serial digital input module optional ET-MD95SD1 for 480i/576i SD signal Business-use digital video deck ET-MD95SD2 for 480p/480i/576i ET-MD95SD3 for HD SDI Auto Connecting signals to the DVI signal input module Pin No SignalDVI-D input module optional How to install the projection lens How to remove the projection lensPull the projection lens Powering up the projector Making adjustment and selectionPress the l button. on the main unit or the remote control Roughly adjust the focus of the lens. Refer to Powering off the projector Projection How to adjust the lens Adjustment range after lens position optical shiftChoose an item and adjust it using Buttons Floor projection Floor projection Ceiling projection Be sure to tighten the fixing screws beforeTransportation Automatic adjustment Auto Setup Registration of input signal data NEW Signal Input screen will be displayedRegistration of new data Press the Menu button If new registration is not available because of full memory Confirm overwriting registration screen will be displayed How to register into sub memory How to erase sub memoryChange registered signals screen will appear Sub memory On-screen indications RestrictionsDesignation can be set by the sub memory items Using the Freeze function Using the Shutter functionUsing the digital zoom D.ZOOM + function On-screen menus Structure of menu screens Menu items setting Resetting to the factory defaultBasic operations on menu screen Returning to the previous screen Adjusting the picture Switching the picture modeSwitching the AI control Select Picture Mode with the buttons Adjusting Contrast / Bright / Color / Tint Adjustment procedure to adjust picture color intensityAdjust the level with Buttons Repeat Steps To adjust BRIGHT, Color or Tint Adjusting the color temperature Operation Adjustment RemarksUSER, STANDARD, NATURAL, CINEMA, Graphic Adjusting color matching Procedure of adjustmentSelect the desired color for adjustment With the buttons Select Picture with the buttons Press Enter button Sharpness / Gamma / Noise reduction / Pulldown mode Adjustment items OperationSelect Picture with the buttons Signal level To input Betacam with YCbCrTo set the sRGB compliant picture Smpte Adjusting the position Shift adjustment Size adjustment Size adjustment screen will be displayed Size modes Blanking adjustment Select Blanking with the buttons Press the Enter button Clock phase adjustment Adjusting the input resolution Input Resolution screen will be displayedTotal DOTS, Displayed DOTS, Total Lines and Displayed Lines Adjusting the clamp position Select Position with the buttons Press the Enter buttonClamp Position screen will be displayed Value changes from 1 to Adjust the Keystone horizontally With the buttons Adjust the vertical Linearity with ButtonsKeystone distortion correction Select Keystone with the buttons Press the Enter button Edge blending adjustment Specify the area to be adjusted with the buttonsTo display the adjustment marker Adjustment marker Changing the display language Select the Bright with the buttons Press the Enter buttonSelect the Language with the buttons Press the Enter button How to change the system format Procedure of setting Video Setting screen will be displayedSelect Option with the buttons Press the Enter button Option screen will be displayed How to use RGB Reality mode Option settings ID number settingID number need not be set when only one projector is used Installation Setting FRONT-F FRONT-C REAR-C REAR-F Lamp power Lamp selectLamp cooling time RGB2 select Video setting Automatic adjustmentSystem information Fan control Main window SubwindowFrame lock Type Setting FUNC1 PasswordList of P in P Setting the contrast mode Select Option with the buttons Press Enter buttonMode ContrastNormal Maximum Brightness Maximum Normal These buttons toggle between 75 Ω and HI-Z TTL SYNC. TermHI-Z TTL Using the serial terminals Pin assignments and signal namesCommunication conditions Factory setting Examples of connection Procedure of setting communication conditions RS232C Setting screen will be displayedPress and buttons to select Option Press the Enter button Control commands Cable specificationsConnecting to a PC Computer Projector DTE specifications Using the Remote 2 terminal Pin assignments and controlSub 9-pin female External appearance Displaying the internal test pattern RS-422 control functionsCycle of displayed internal test patterns How to use network module optional Example of connectionName and function of network module parts Initial setting of network module Network Setting screen will be displayedMenu screen will be displayed Address automatically using the Dhcp server Items Function DescriptionSet to OFF if Dhcp server is not used Port No Accessing from the Web browser Network setting Top Network setting Projector control Status indication Mail setting Smtp Mail setting page continuing How to use network module optional For control of image files Indication of monitor lamp Lamp Information Checkpoint Remedial measureIndication Monitor Cleaning and replacement of air filter Procedure of cleaningClean the air filter Dismantle the air filter Replacement of lamp unit Timing of lamp unit replacement Procedure of lamp unit replacement Fixing screws Lamp unit cover Press the Enter button. When OK? is displayed, press An item Lamp Reset will be addedUsed hours of the specified lamp unit will be reset to zero Symptoms Checkpoint Power does not turn onRemote control does No image appears on Specifications PT-D7500U PT-D7500U PT-D7600U Compatible RGB/YPBPR Signals Appendix Outside dimensions 530 Units mminch Concernant LA Sécurité Précautions concernant la sécurité Ne pas couvrir le filtre et la sortie d’airNe pas surcharger la prise de courant Ne pas retirer le couvercle ou le modifier Ne pas placer le projecteur sur des surfaces instables Ne pas placer des récipients de liquide sur le projecteurNe démontez pas le bloc lampe Ne pas mettre d’objets étrangers dans le projecteur ’utiliser que la pile indiquée Nutilisez pas un bloc lampe usagéCela peut entraîner une rupture de la lampe Sinon cela peut causer des chocs électriques Nettoyage et maintenance Précautions pour la manipulationMise au rebut Remplacement de la lampe Période de remplacement de la lampe Procédure de remplacement de la lampe La lampe est chaude si elle vient d’être utiliséeVis de fixation Cache de la lampe 111 Professional/Industrial Video Technical Support800 FAX 201 Mail pbtssupport@panasonic.com Panasonic Canada Inc