Parker Hannifin GEM6K Ntid, Network Sharing Unit ID for Peer-to-Peer Communication, Product

NTID

Type:

Syntax:

Units:

Range:

Default:

Response:

See Also:

Network Sharing Unit ID for Peer-to-Peer Communication

Network		Product	Rev
<!>NTID<i>		6K	5.3
n/a
i =	0-8
i =	0 (receive variable data only, do not send variable data)
NTID		*NTID2

NTRATE, VARSHI, VARSHO

The NTID command establishes the Network Unit ID for a 6K unit involved in a peer-to-peer Ethernet connection with other 6K or Gem6K products. Up to eight 6K or Gem6K products may be connected in the peer-to-peer network.

Saved in Non-Volatile Memory

This command is saved in the controller’s non-volatile memory, and is remembered on power-up and RESET.

Implementation process for peer-to-peer communication (further details are provided in the Programmer’s Guide):

1.Connect the 6K/Gem6K products to the network and configure each 6K/Gem6K for Ethernet communication according to the Ethernet Networking configuration procedures in the Programmer’s Guide.

2.Set the broadcasting rate with NTRATE command, preferably the same rate (50 milliseconds is recommended) for each unit.

3.If the unit is to receive data only (not send) you are finished with the setup for that unit. If the unit is to also send, complete steps 4 and 5.

4.Assign a unique unit number (1-8) with the NTID command.

5.Assign data to the broadcast variables (up to eight) with the VARSHO command.

6.Repeat steps 2-5 for each unit in the peer-to-peer network.

Example:

;*************************************************************************************

;CONNECT TO 6K UNIT #1 AND SEND THE FOLLOWING SETUP COMMANDS

NTID1	; Assign this unit a				peer-to-peer unit			#1
VARSHO1 = 1A	;	Shared	variable	#1	contains	axis	1's	acceleration
VARSHO2 = 1PE	;	Shared	variable	#2	contains	axis	1's	encoder position

;```````````````````````````````````````````````````````````````````````

;` Use this space to define shared output variables VARSHO3 – VARSHO7. `

;```````````````````````````````````````````````````````````````````````

VARSHO8 = VARI1	;	Shared variable #8 contains the value of	VARI1
NTRATE50	;	Unit #1 will broadcast at 50-millisecond	intervals

;*************************************************************************************

;*************************************************************************************

;CONNECT TO 6K UNIT #2 AND SEND THE FOLLOWING SETUP COMMANDS

NTID2	; Assign this unit a				peer-to-peer unit			#2
VARSHO1 = 1D	;	Shared	variable	#1	contains	axis	1's	programmed distance
VARSHO2 = 3PE	;	Shared	variable	#2	contains	axis	3's	encoder position

;```````````````````````````````````````````````````````````````````````

;` Use this space to define shared output variables VARSHO3 – VARSHO7. `

;```````````````````````````````````````````````````````````````````````

VARSHO8 = 1ANI.1	; Shared variable		#8 contains the voltage value at analog
NTRATE50	;	input #1 on I/O	brick #1
	;	Unit #2 will broadcast at 50-millisecond intervals

;*************************************************************************************

;*************************************************************************************

;CONNECT TO 6K UNIT #3 AND SEND THE FOLLOWING SETUP COMMANDS

NTRATE50 ; Unit #3 will broadcast at 50-millisecond intervals

;This third unit will receive data only. Therefore, it does

;not require a unit ID number or VARSHO data assignment.

;*************************************************************************************

page 18