Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic manual OnSite 1052 &1063 Series, Metro-Optical Transport Access Nodes

Models: 1063 07MOS10xx-GS

1 67

Download 67 pages 15.67 Kb

Page 1

OnSite 1052 &1063 Series

OnSite 1052 &1063 Series

Metro-Optical Transport

Access Nodes

Getting Started Guide

The compliance information in this document is incomplete and subject to change.

IMPORTANT

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail:support@patton.com

WWW: www.patton.com

Part Number: 07MOS10xx-GS, Rev. A

Revised: November 20, 2009

Image 1

Patton electronic manual OnSite 1052 &1063 Series, Metro-Optical Transport Access Nodes, Getting Started Guide

Contents

OnSite 1052 &1063 Series Metro-Optical Transport Access NodesGetting Started Guide Sales Ofﬁce +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Summary Table of Contents Table of ContentsTable of Contents Installation OverviewSpecifications System Management AccessContacting Patton for assistance Compliance informationC Terms and Acronyms List of Figures List of Tables Audience About this guideStructure PrecautionsGeneral conventions Typographical conventions used in this documentMouse conventions Power Cable Safety when using electricityFiber-Optic Safety Precautions Optical SafetyElectrostatic Discharge Damage Fiber-Optic PortsChapter 1 Product Overview Chapter contentsOnSite Platforms Introduction21-port E1 3-port DS3/E3 2-port STM-1 optical and electrical Figure 4. OS1063 Base System Figure 3. OS1052 Base SystemChapter contents Chapter 2 Application OverviewFigure 5. Typical OS1052 application OS1052 Application2 Application Overview OS1052 ApplicationThe base OS1052 system is conﬁgured with 2 STM-1 8 E1/T1 2 Ethernet Figure 7. Typical OS1063 application OS1063 Application2 Application Overview OS1063 ApplicationFigure 8. OS1063 Map + Modules Chapter Installation OverviewChapter contents Site Preparation Unpacking and InspectionTo check the contents of the shipping cartons, follow these steps IntroductionPlanning Your Site Site EnvironmentSite Requirements Distribution rack requirements Operating Environment RequirementsDistribution Rack Requirements Power Supply RequirementsTo operate your OS-10 equipment safely, follow these requirements Protective Grounding for the Rack and Chassis Mechanical Recommendations for the RackSpace Requirements for the Rack Securing the RackOnSite System Installation Tools and Equipment for Installation and MaintenanceMounting the Chassis to an EIA/TIA 19-Inch Rack OnSite System Installation Mounting the Chassis to an ETSI RackFigure 11. Mounting the OS-10 System in an ETSI 300-mm Rack 3 Installation OverviewFigure 12. Mounting the OS-10 System Chassis on a Wall Mounting the Chassis on the WallConnecting Power to the OS-10 System Installing the Chassis Ground ConnectionThe input voltage tolerance limits for AC power are 100 to 245 VAC Connecting AC Power to the OS-10 SystemConnecting DC Power to the OS-10 System Powering On the OS-10 System with AC PowerWiring Procedure for DC Input Power To power on the OS-10 system using AC power, follow these steps2. Remove power from this circuit 5. Connect the positive lead of the circuit to the return direction for “A” power on the OS-10 system termi- nal block. See wiring 2-A in Figure Checking the OS-10 System Installation Chapter contents System Management AccessChapter 4 System Management Access General OverviewIntroduction Ethernet LAN Management Port Serial Management Port Access through the Serial Port Gaining Access to the Systemsave config Access through the Ethernet LAN Management PortLaunching the GUI Application Web-Based Management InterfaceFigure 17. Web-Based Management GUI Frames Autonomous Alarm Messages Figure 19. Conﬁguring an Authorized OnSight NMS Server 1. On the Authorized NMS Servers page, click on AddEngineering Orderwire EOW The EOW port supports dual-tone multifrequency DTMF signaling to identify EOW stations within an OnSite OS-10 subnetwork. Each EOW station is identiﬁed with a programmable 3-digit station ID number 8. Click on Apply to complete the conﬁguration of the EOW port At this point, the called station begins to ring if another telephone set is connected to the EOW port of that station Chapter contents Chapter 5 Contacting Patton for assistanceWarranty coverage Warranty Service and Returned Merchandise Authorizations RMAsOut-of-warranty service Contact informationRMA numbers Return for credit policyShipping instructions Patton Electronics CompanyChapter contents Appendix A Compliance informationCompliance SafetyRadio and TV Interference FCC Part 68 ACTA StatementAuthorized European Representative Declaration of ConformityChapter contents Appendix B SpeciﬁcationsModel OS1052 System AccessTrunk Interfaces Client InterfacesWeight DimensionsPower OperationsSystem Access Model OS1063Trunk Interfaces Client InterfacesWeight DimensionsPower OperationsChapter contents Appendix C Terms and AcronymsAbbreviation AbbreviationsMeaning Meaning AbbreviationMeaning Abbreviation