Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 07MOS10xx-GS, 1063 manual List of Tables

Models: 1063 07MOS10xx-GS

1 67

Download 67 pages 15.67 Kb

Page 8

List of Tables

List of Tables
1	General conventions	11
2	Mouse conventions	11
3	Base System Configuration for OnSite Platforms	16
4	Environmental Conditions for Operating the OS-10 System	26
5	Power Requirements for the OS-10 System	27
6	Ground Wire Specifications	33
7	OS-10 Power Options	33
8	Power Consumption	34
9	DC Wiring Requirements for the OS-10 System Chassis	35
10	Ethernet LAN Management Port Cabling Specifications	41
11	Pin Assignments for the Ethernet LAN Management Port	42
12	Pin Assignments for the RS-232 Serial Management Port	42
13	RS-232 Serial Port Parameters	42
14	VT100 Terminal Emulation Settings	42
15	Web-Based Management GUI Frame Descriptions	46

8

Image 8

Patton electronic 07MOS10xx-GS, 1063 manual List of Tables

Contents

Metro-Optical Transport Access Nodes OnSite 1052 &1063 SeriesGetting Started Guide Sales Ofﬁce +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Table of Contents Summary Table of ContentsTable of Contents Installation OverviewSystem Management Access SpecificationsContacting Patton for assistance Compliance informationC Terms and Acronyms List of Figures List of Tables About this guide AudiencePrecautions StructureMouse conventions Typographical conventions used in this documentGeneral conventions Safety when using electricity Power CableOptical Safety Fiber-Optic Safety PrecautionsElectrostatic Discharge Damage Fiber-Optic PortsChapter contents Chapter 1 Product OverviewIntroduction OnSite Platforms21-port E1 3-port DS3/E3 2-port STM-1 optical and electrical Figure 3. OS1052 Base System Figure 4. OS1063 Base SystemChapter 2 Application Overview Chapter contentsOS1052 Application Figure 5. Typical OS1052 application2 Application Overview OS1052 ApplicationThe base OS1052 system is conﬁgured with 2 STM-1 8 E1/T1 2 Ethernet OS1063 Application Figure 7. Typical OS1063 application2 Application Overview OS1063 ApplicationFigure 8. OS1063 Map + Modules Chapter contents Installation OverviewChapter Unpacking and Inspection Site PreparationTo check the contents of the shipping cartons, follow these steps IntroductionSite Requirements Site EnvironmentPlanning Your Site Operating Environment Requirements Distribution rack requirementsTo operate your OS-10 equipment safely, follow these requirements Power Supply RequirementsDistribution Rack Requirements Mechanical Recommendations for the Rack Protective Grounding for the Rack and ChassisSpace Requirements for the Rack Securing the RackMounting the Chassis to an EIA/TIA 19-Inch Rack Tools and Equipment for Installation and MaintenanceOnSite System Installation Mounting the Chassis to an ETSI Rack OnSite System Installation3 Installation Overview Figure 11. Mounting the OS-10 System in an ETSI 300-mm RackMounting the Chassis on the Wall Figure 12. Mounting the OS-10 System Chassis on a WallInstalling the Chassis Ground Connection Connecting Power to the OS-10 SystemConnecting AC Power to the OS-10 System The input voltage tolerance limits for AC power are 100 to 245 VACPowering On the OS-10 System with AC Power Connecting DC Power to the OS-10 SystemWiring Procedure for DC Input Power To power on the OS-10 system using AC power, follow these steps2. Remove power from this circuit 5. Connect the positive lead of the circuit to the return direction for “A” power on the OS-10 system termi- nal block. See wiring 2-A in Figure Checking the OS-10 System Installation Chapter System Management AccessChapter contents Introduction General Overview4 System Management Access Ethernet LAN Management Port Serial Management Port Gaining Access to the System Access through the Serial PortAccess through the Ethernet LAN Management Port save configWeb-Based Management Interface Launching the GUI ApplicationFigure 17. Web-Based Management GUI Frames Autonomous Alarm Messages 1. On the Authorized NMS Servers page, click on Add Figure 19. Conﬁguring an Authorized OnSight NMS ServerEngineering Orderwire EOW The EOW port supports dual-tone multifrequency DTMF signaling to identify EOW stations within an OnSite OS-10 subnetwork. Each EOW station is identiﬁed with a programmable 3-digit station ID number 8. Click on Apply to complete the conﬁguration of the EOW port At this point, the called station begins to ring if another telephone set is connected to the EOW port of that station Chapter 5 Contacting Patton for assistance Chapter contentsWarranty Service and Returned Merchandise Authorizations RMAs Warranty coverageOut-of-warranty service Contact informationReturn for credit policy RMA numbersShipping instructions Patton Electronics CompanyAppendix A Compliance information Chapter contentsSafety ComplianceRadio and TV Interference FCC Part 68 ACTA StatementDeclaration of Conformity Authorized European RepresentativeAppendix B Speciﬁcations Chapter contentsSystem Access Model OS1052Trunk Interfaces Client InterfacesDimensions WeightPower OperationsModel OS1063 System AccessTrunk Interfaces Client InterfacesDimensions WeightPower OperationsAppendix C Terms and Acronyms Chapter contentsMeaning AbbreviationsAbbreviation Abbreviation MeaningAbbreviation Meaning