Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 1063 Mounting the OS-10 System in an ETSI 300-mm Rack, Installation Overview

Models: 1063 07MOS10xx-GS

1 67

Download 67 pages 15.67 Kb

Page 31

Figure 11. Mounting the OS-10 System in an ETSI 300-mm Rack

OnSite Series Getting Started Guide	3 • Installation Overview

Note Do not cover vents that would restrict airﬂow. Leave a minimum of a half-rack space above and below the OS-10 system for adequate ven- tilation.

3.Secure the chassis using four 12-24 x 3/4-inch screws (two screws for each side) through the elongated holes in the L bracket nearest to the chassis and to the threaded holes in the mounting post. Use a suitable screwdriver for this task.

4.Tighten any loose captive installation screws on the expansion slot front panel covers.

Figure 11. Mounting the OS-10 System in an ETSI 300-mm Rack

OnSite System Installation

31

Image 31

Patton electronic 1063, 07MOS10xx-GS manual Mounting the OS-10 System in an ETSI 300-mm Rack, Installation Overview

Contents

Sales Ofﬁce +1 301 Metro-Optical Transport Access NodesOnSite 1052 &1063 Series Getting Started Guide7622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Installation Overview Table of ContentsSummary Table of Contents Table of ContentsCompliance information System Management AccessSpecifications Contacting Patton for assistanceC Terms and Acronyms List of Figures List of Tables Audience About this guideStructure PrecautionsGeneral conventions Typographical conventions used in this documentMouse conventions Power Cable Safety when using electricityFiber-Optic Ports Optical SafetyFiber-Optic Safety Precautions Electrostatic Discharge DamageChapter 1 Product Overview Chapter contentsOnSite Platforms Introduction21-port E1 3-port DS3/E3 2-port STM-1 optical and electrical Figure 4. OS1063 Base System Figure 3. OS1052 Base SystemChapter contents Chapter 2 Application OverviewOS1052 Application OS1052 ApplicationFigure 5. Typical OS1052 application 2 Application OverviewThe base OS1052 system is conﬁgured with 2 STM-1 8 E1/T1 2 Ethernet OS1063 Application OS1063 ApplicationFigure 7. Typical OS1063 application 2 Application OverviewFigure 8. OS1063 Map + Modules Chapter Installation OverviewChapter contents Introduction Unpacking and InspectionSite Preparation To check the contents of the shipping cartons, follow these stepsPlanning Your Site Site EnvironmentSite Requirements Distribution rack requirements Operating Environment RequirementsDistribution Rack Requirements Power Supply RequirementsTo operate your OS-10 equipment safely, follow these requirements Securing the Rack Mechanical Recommendations for the RackProtective Grounding for the Rack and Chassis Space Requirements for the RackOnSite System Installation Tools and Equipment for Installation and MaintenanceMounting the Chassis to an EIA/TIA 19-Inch Rack OnSite System Installation Mounting the Chassis to an ETSI RackFigure 11. Mounting the OS-10 System in an ETSI 300-mm Rack 3 Installation OverviewFigure 12. Mounting the OS-10 System Chassis on a Wall Mounting the Chassis on the WallConnecting Power to the OS-10 System Installing the Chassis Ground ConnectionThe input voltage tolerance limits for AC power are 100 to 245 VAC Connecting AC Power to the OS-10 SystemTo power on the OS-10 system using AC power, follow these steps Powering On the OS-10 System with AC PowerConnecting DC Power to the OS-10 System Wiring Procedure for DC Input Power2. Remove power from this circuit 5. Connect the positive lead of the circuit to the return direction for “A” power on the OS-10 system termi- nal block. See wiring 2-A in Figure Checking the OS-10 System Installation Chapter contents System Management AccessChapter 4 System Management Access General OverviewIntroduction Ethernet LAN Management Port Serial Management Port Access through the Serial Port Gaining Access to the Systemsave config Access through the Ethernet LAN Management PortLaunching the GUI Application Web-Based Management InterfaceFigure 17. Web-Based Management GUI Frames Autonomous Alarm Messages Figure 19. Conﬁguring an Authorized OnSight NMS Server 1. On the Authorized NMS Servers page, click on AddEngineering Orderwire EOW The EOW port supports dual-tone multifrequency DTMF signaling to identify EOW stations within an OnSite OS-10 subnetwork. Each EOW station is identiﬁed with a programmable 3-digit station ID number 8. Click on Apply to complete the conﬁguration of the EOW port At this point, the called station begins to ring if another telephone set is connected to the EOW port of that station Chapter contents Chapter 5 Contacting Patton for assistanceContact information Warranty Service and Returned Merchandise Authorizations RMAsWarranty coverage Out-of-warranty servicePatton Electronics Company Return for credit policyRMA numbers Shipping instructionsChapter contents Appendix A Compliance informationFCC Part 68 ACTA Statement SafetyCompliance Radio and TV InterferenceAuthorized European Representative Declaration of ConformityChapter contents Appendix B SpeciﬁcationsClient Interfaces System AccessModel OS1052 Trunk InterfacesOperations DimensionsWeight PowerClient Interfaces Model OS1063System Access Trunk InterfacesOperations DimensionsWeight PowerChapter contents Appendix C Terms and AcronymsAbbreviation AbbreviationsMeaning Meaning AbbreviationMeaning Abbreviation