Manuals / Patton electronic / Computer Equipment / Network Router

Patton electronic 07MOS10xx-GS Model OS1052, Trunk Interfaces, Client Interfaces, Protection

Models: 1063 07MOS10xx-GS

1 67

Download 67 pages 15.67 Kb

Page 60

Model OS1052

OnSite Series Getting Started Guide	B • Specifications

Model OS1052

Trunk Interfaces

STM-1: G.707, G.783

Optics: G.957 S-1.1, L-1.1 and L-1.2 options

Client Interfaces

E1: G.703, 75-ohm and 120-ohm options

T1: G.703, 100-ohm

Ethernet 10/100Base-TX: 802.3u

Expansion Modules

SDH: STM-1 optical (2 ports) • STM-1 electrical (2 ports)

PDH: E1 (21 ports) • E3/DS3 (3 ports)

Packet Data: 10/100Base-TX (8 ports)

Conﬁguration & Port Capacity for 2 Expansion Slots

STM-1:Base: 2 • Max: 6

E1: Base: 8 • Max: 50

E3/DS3: Base: – • Max: 6

10/100Base-TX:Base: 2 • Max: 18

Protection

Linear MSP 1+1 • SNCP/I and SNCP/N

Bandwidth Connectivity and Provisioning

Connectivity: VC-12, VC-3 levels

One-way, two-way, drop-and-continue and multicast connections

VCAT: VC-12-Xv and VC-3-Xv

LCAS: G.7042

Packet encapsulation: GFP-F (G.7041)

Timing & Synchronization

Internal: Stratum 3 clock

Line timing: STM-1 and E1/T1

External timing: Dual Sync In/Out ports at 2 or 1.5 Mbps/MHz

SSM support: G.781

System Access

Serial RS-232 and Ethernet LAN management ports

IP over DCCr and DCCm options

IP over E1 signal mapped into selected VC-12 channel

DCC transparency (any subset of DCC rows)

Telnet

Model OS1052

60

Image 60

Patton electronic 07MOS10xx-GS, 1063 manual Model OS1052, Trunk Interfaces, Client Interfaces, Expansion Modules, Protection

Contents

Metro-Optical Transport Access Nodes OnSite 1052 &1063 SeriesGetting Started Guide Sales Ofﬁce +1 3017622 Rickenbacker Drive Gaithersburg, MD 20879 USA Tel +1 301 Summary Table of Contents Table of Contents Summary Table of ContentsTable of Contents Installation OverviewSystem Management Access SpecificationsContacting Patton for assistance Compliance informationC Terms and Acronyms List of Figures List of Tables About this guide AudiencePrecautions StructureTypographical conventions used in this document General conventionsMouse conventions Safety when using electricity Power CableOptical Safety Fiber-Optic Safety PrecautionsElectrostatic Discharge Damage Fiber-Optic PortsChapter contents Chapter 1 Product OverviewIntroduction OnSite Platforms21-port E1 3-port DS3/E3 2-port STM-1 optical and electrical Figure 3. OS1052 Base System Figure 4. OS1063 Base SystemChapter 2 Application Overview Chapter contentsOS1052 Application Figure 5. Typical OS1052 application2 Application Overview OS1052 ApplicationThe base OS1052 system is conﬁgured with 2 STM-1 8 E1/T1 2 Ethernet OS1063 Application Figure 7. Typical OS1063 application2 Application Overview OS1063 ApplicationFigure 8. OS1063 Map + Modules Installation Overview ChapterChapter contents Unpacking and Inspection Site PreparationTo check the contents of the shipping cartons, follow these steps IntroductionSite Environment Planning Your SiteSite Requirements Operating Environment Requirements Distribution rack requirementsPower Supply Requirements Distribution Rack RequirementsTo operate your OS-10 equipment safely, follow these requirements Mechanical Recommendations for the Rack Protective Grounding for the Rack and ChassisSpace Requirements for the Rack Securing the RackTools and Equipment for Installation and Maintenance OnSite System InstallationMounting the Chassis to an EIA/TIA 19-Inch Rack Mounting the Chassis to an ETSI Rack OnSite System Installation3 Installation Overview Figure 11. Mounting the OS-10 System in an ETSI 300-mm RackMounting the Chassis on the Wall Figure 12. Mounting the OS-10 System Chassis on a WallInstalling the Chassis Ground Connection Connecting Power to the OS-10 SystemConnecting AC Power to the OS-10 System The input voltage tolerance limits for AC power are 100 to 245 VACPowering On the OS-10 System with AC Power Connecting DC Power to the OS-10 SystemWiring Procedure for DC Input Power To power on the OS-10 system using AC power, follow these steps2. Remove power from this circuit 5. Connect the positive lead of the circuit to the return direction for “A” power on the OS-10 system termi- nal block. See wiring 2-A in Figure Checking the OS-10 System Installation System Management Access Chapter contentsChapter General Overview 4 System Management AccessIntroduction Ethernet LAN Management Port Serial Management Port Gaining Access to the System Access through the Serial PortAccess through the Ethernet LAN Management Port save configWeb-Based Management Interface Launching the GUI ApplicationFigure 17. Web-Based Management GUI Frames Autonomous Alarm Messages 1. On the Authorized NMS Servers page, click on Add Figure 19. Conﬁguring an Authorized OnSight NMS ServerEngineering Orderwire EOW The EOW port supports dual-tone multifrequency DTMF signaling to identify EOW stations within an OnSite OS-10 subnetwork. Each EOW station is identiﬁed with a programmable 3-digit station ID number 8. Click on Apply to complete the conﬁguration of the EOW port At this point, the called station begins to ring if another telephone set is connected to the EOW port of that station Chapter 5 Contacting Patton for assistance Chapter contentsWarranty Service and Returned Merchandise Authorizations RMAs Warranty coverageOut-of-warranty service Contact informationReturn for credit policy RMA numbersShipping instructions Patton Electronics CompanyAppendix A Compliance information Chapter contentsSafety ComplianceRadio and TV Interference FCC Part 68 ACTA StatementDeclaration of Conformity Authorized European RepresentativeAppendix B Speciﬁcations Chapter contentsSystem Access Model OS1052Trunk Interfaces Client InterfacesDimensions WeightPower OperationsModel OS1063 System AccessTrunk Interfaces Client InterfacesDimensions WeightPower OperationsAppendix C Terms and Acronyms Chapter contentsAbbreviations AbbreviationMeaning Abbreviation MeaningAbbreviation Meaning