Adjustment
12.08.03 | List of parameters |
|
|
| |||||
|
|
|
|
|
|
|
|
| |
|
| Group | Parameter | Description |
| User level | Setting range | Set value | |
|
|
|
|
|
|
|
|
| |
|
| 1 | 101 | Control panel key tone |
| A, B, C |
| ON | |
|
|
|
| (0FF = AUS, ON = EIN) |
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
| 6 | 605 | Speed display |
| B, C |
| OFF | |
|
|
|
| (0FF = AUS, ON = EIN) |
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
| 607 | Max. speed |
| B, C | 300 - 6000 | 4500 | |
|
|
|
|
|
|
|
|
| |
|
|
| 609 | Cutting speed |
| B, C | 60 - 500 | 180 | |
|
|
|
|
|
|
|
|
| |
|
|
| 660 | Bobbin thread control |
| A, B, C | 0 - 2 | 0 | |
|
|
|
| 0 | = off |
|
|
|
|
|
|
|
| 1 | = thread monitor |
|
|
|
|
|
|
|
| 2 | = reverse counter |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| 7 | 700 | Needle position 0 |
| B, C | 0 - 255 |
| |
|
|
|
| (needle reference position) |
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
| 702 | Needle position 1 (needle lowered) |
| B, C | 0 - 255 | 70 | |
|
|
|
|
|
|
|
|
| |
|
|
| 703 | Needle position 2 |
| B, C | 0 - 255 | 222 | |
|
|
|
|
|
|
|
|
| |
|
|
| 705 | Needle position 5 (end of cutting signal 1) |
| B, C | 0 - 255 | 196 | |
|
|
|
|
|
|
|
|
| |
|
|
| 706 | Needle position 6 (start of cutting signal 2) |
| B, C | 0 - 255 | 136 | |
|
|
|
|
|
|
|
|
| |
|
|
| 707 | Needle position 9 |
| B, C | 0 - 255 | 150 | |
|
|
|
| (start thread tension release) |
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
| 797 | Hardware test |
| B, C |
| OFF | |
|
|
|
| (0FF = AUS, ON = EIN) |
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
| 798 | User level |
| A, B, C | 0, 1, 11 | 0 | |
|
|
|
| 0 | = User level"A" |
|
|
|
|
|
|
|
| 1 | = Mechanic level"B" |
|
|
|
|
|
|
|
| 11 = Service level"C" |
|
|
|
| |
|
|
|
|
|
|
|
|
| |
|
|
| 799 | Machine class |
| C | 1 - 2 | 1 | |
|
|
|
| 1 | = 918 / 938 |
|
|
|
|
|
|
|
| 2 | = - |
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
| 8 | 800 | Rotating direction of the motor |
| C | 0 - 1 | 1 | |
|
|
|
| 1 | = 918 / 938 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Further parameters are listed in theMotorInstructionManual.
12 - 45