Pioneer DEX-P99RS Using the time alignment, Press B to cancel the network adjust- ment mode

Section

03Audio Adjustments

4Push MULTI-CONTROL left or right to select the cut-off frequency (crossover fre- quency) of the selected speaker unit (fil- ter).

Each time MULTI-CONTROL is pushed left or right, cut-off frequencies (crossover frequen- cies) are selected in the following order:

!High-LPF

5k—6.3k—8k—10k—12.5k—16k—20k

!High-HPF

800Hz—1k—1.25k—1.6k—2k—2.5k— 3.15k—4k—5k—6.3k—8k—10k—12.5k— 16k

!Mid-LPF, Low-LPF and SW-LPF

25Hz—31.5Hz—40Hz—50Hz—63Hz— 80Hz—100Hz—125Hz—160Hz—200Hz— 250Hz—315Hz—400Hz—500Hz—630Hz

—800Hz—1k—1.25k—1.6k—2k—2.5k— 3.15k—4k—5k—6.3k—8k—10k—12.5k— 16k—20k

!Mid-HPF, Low-HPF and SW-HPF

20Hz—25Hz—31.5Hz—40Hz—50Hz— 63Hz—80Hz—100Hz—125Hz—160Hz— 200Hz—250Hz—315Hz—400Hz—500Hz

—630Hz—800Hz—1k—1.25k—1.6k—2k

—2.5k—3.15k—4k—5k—6.3k—8k—10k

—12.5k—16k

#You cannot select speakers that are set to off in the initial setting. Refer to Setting the speakers on page 35.

5Push MULTI-CONTROL up or down to adjust the level of the selected speaker unit (filter).

Each time MULTI-CONTROL is pushed up or down, the level of the selected speaker unit (fil- ter) increases or decreases.

0dB to –24 dB is displayed as the level is in- creased or decreased if you have selected High-LPF, High-HPF, Mid-LPF or Mid-HPF.

6dB to –24 dB is displayed as the level is in- creased or decreased, only if you have se- lected Low-LPF, Low-HPF, SW-LPF or SW-HPF.

6Turn MULTI-CONTROL to select NW 3 in the audio function menu.

Refer to Introduction of audio adjustments on page 24.

7Push MULTI-CONTROL left or right to select the slope of the selected speaker unit (filter).

Each time MULTI-CONTROL is pushed left or right, slopes are selected in the following order:

!High-HPF

6dB/oct.—12dB/oct.—18dB/oct.— 24dB/oct.—30dB/oct.—36dB/oct.

!High-LPF, Mid-LPF, Mid-HPF, Low-LPF, Low-HPF, SW-LPF and SW-HPF Pass—6dB/oct.—12dB/oct.—18dB/oct.— 24dB/oct.—30dB/oct.—36dB/oct.

8Push MULTI-CONTROL up or down to switch the phase of the selected speaker unit (filter).

Push MULTI-CONTROL up selects normal phase and NOR appears in the display. Push MULTI-CONTROL down selects reverse phase

and REV appears in the display.

# You can adjust the parameters for other speaker units (filters) in the same way.

9Press B to cancel the network adjust- ment mode.

Using the time alignment

The time alignment lets you adjust the dis- tance between each speaker and the listening position.

1Use MULTI-CONTROL to select TA1 in the audio function menu.

Refer to Introduction of audio adjustments on page 24.

28 En