Useful adjustment settings
Chapter 9
Useful adjustment settings
09
English
Switching the vertical drive frequency
You can switch the vertical drive frequency for screen display between 75 Hz and 100 Hz. Choose the drive frequency that best suits the broadcast signals in your area.
1 | Press HOME MENU. |
|
|
2 | Select “Option“ ( | then ENTER). | |
3 | Select “Drive Mode“ ( | then ENTER). | |
4 | Select “75 Hz“ or “100 Hz“ ( | then ENTER). | |
Drive Mode
75Hz
100Hz
5 Press HOME MENU to exit the menu.
Note
•This setting can be made for each input source separately.
•Selections are effective only for the following input signals: PAL/SECAM, 576i, 576p, 1080i@50 Hz, 720p@50 Hz.
•This setting cannot be made when 480i, 480p, 1080i@60 Hz, 720p@60 Hz, or 1080p@24 Hz signals are input.
•If you select “Auto” for “Side Mask” (page 37), the selection for “Drive Mode” becomes ineffective.
Adjusting image positions (AV mode only)
Adjust the horizontal and vertical positions of images on the plasma display.
1 | Press HOME MENU. |
|
|
| ||
2 | Select “Option“ ( | then ENTER). |
| |||
3 | Select “Position“ ( | then ENTER). |
| |||
4 | Select “H/V Position Adjust“ ( | then ENTER). |
| |||
|
|
|
|
|
|
|
|
|
| Position |
|
|
|
|
|
| H/V Position Adjust |
|
|
|
|
|
| Reset |
|
|
|
|
|
|
|
| ||
5 | Adjust the vertical position ( | ) or the horizontal | ||||
position ( | ). |
|
|
| ||
6 | Press HOME MENU to exit the menu. |
| ||||
| Note |
|
|
| ||
| • To restore the factory defaults for all items, press | to select | ||||
| "Reset" in step 4, and then press ENTER. A confirmation screen | |||||
| appears. Press | to select "Yes", and then press ENTER. | ||||
• Adjustments are stored separately according to input source.
•Depending on the displayed video, the image position may not change even after adjustment.
Adjusting image positions and clock automatically (PC mode only)
Use Auto Setup to automatically adjust the positions and clock of images coming from a personal computer.
1 | Press HOME MENU. |
|
2 | Select “Option“ ( | then ENTER). |
3 | Select “Auto Setup“ ( | then ENTER). |
Option
Auto Setup
Manual Setup
• Auto Setup starts.
4 Press HOME MENU to exit the menu.
Note
•When Auto Setup is finished, "Auto Setup completed." appears.
•Even when "Auto Setup completed." appears, Auto Setup may have failed, depending on conditions.
•Auto Setup may fail with a PC image composed of similar patterns or monochrome. If not successful, change the PC image and try again.
•Be sure to connect the computer to the plasma display and switch it on before starting Auto Setup.
Adjusting image positions and clock manually (PC mode only)
Usually you can easily adjust the positions and clock of images using Auto Setup. Use Manual Setup to optimize the positions and clock of images when necessary.
1 | Press HOME MENU. |
|
|
|
2 | Select “Option“ ( | then ENTER). |
| |
3 | Select “Manual Setup“ ( | then ENTER). | ||
4 | Select the item to be adjusted ( | then ENTER). | ||
| Manual Setup |
|
|
|
| H/V Position Adjust |
|
|
|
| Clock |
|
| 0 |
| Phase |
|
| 0 |
| Reset |
|
|
|
5 Perform adjustment ().
• With "Clock" or "Phase" selected, you can change the
parameter using | . |
35
En
