Quick surround sound setup | 03 |
•ERR Fch – Check the front speaker connections.
•ERR Sch – Check the surround or surround back speaker connections.
•ERR SW – Make sure the subwoofer has been switched on and volume on the subwoofer is turned up.
7 Use and to select the speaker system that corresponds to your setup. Cycle between the following choices:
|
| 2.0ch |
|
| 2.1ch* |
|
|
| 3.0ch |
|
| 3.1ch* |
|
| |||
|
|
|
|
|
|
|
| ||||||||||
7.1ch* |
|
|
|
|
|
|
|
|
| 4.0ch | |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
7.0ch |
|
|
|
|
|
|
|
|
| 4.1ch* | |||||||
|
| 6.1ch* |
|
| 6.0ch |
|
|
| 5.1ch* |
|
| 5.0ch |
|
| |||
|
|
|
|
|
|
|
| ||||||||||
*Indicates a subwoofer is included in your speaker setup
See the table on page 12 if you’re unsure which speaker system to select.
8If you selected a speaker system that includes a subwoofer, press ENTER to check the subwoofer output level.
If the subwoofer output level is too high/low, SW.VOL.UP/SW.VOL.DWN blinks in the display for five seconds. To exit and check your subwoofer output level, press MCACC SETUP (see the notes regarding noise levels below) or simply turn the subwoofer volume up or down (as indicated), then press ENTER when you’re prompted to GO NEXT?
9Press ENTER to finish the auto surround setup.
The system checks for speaker size, channel delay and channel level. If you have connected a subwoofer, it will check for ambient noise once again.
When the auto surround setup is complete, the volume level returns to normal and COMPLETE, then RESUME shows in the display.
|
|
| English | |
• If the room environment is not optimal for | ||||
| ||||
| the auto surround setup (too much |
| ||
| ambient noise, echo off the walls, obsta- |
| ||
| cles blocking the speakers from the |
| ||
| microphone) the final settings may be |
| ||
| incorrect. Check for household appli- | Italiano | ||
| ances (air conditioner, fridge, fan, etc.), | |||
|
| |||
| that may be affecting the environment |
| ||
| and switch them off if necessary. |
| ||
• Some older TVs may interfere with the |
| |||
| operation of the mic. If this seems to be |
| ||
| ||||
| happening, switch off the TV when doing |
| ||
| the auto surround setup. | Français | ||
• Using the MCACC system to set up your | ||||
| ||||
| speaker system overwrites any previous |
| ||
| settings you had for the STANDARD or |
| ||
| ADVANCED SURROUND modes. |
| ||
• When the STANDARD or ADVANCED |
| |||
| SURROUND mode is selected, you can | Deutsch | ||
| check the settings made with MCACC by | |||
|
| |||
| using CH SELECT (to check channel |
| ||
| levels) or by going through the steps in |
| ||
| Choosing your receiver setup on page 43 |
| ||
| to check other settings. |
| ||
• Depending on the the characteristics of | Nederlands | |||
| your room, sometimes identical speakers | |||
|
| |||
| with cone sizes of around 12cm will end |
| ||
| up with different size settings. You can |
| ||
| correct the setting manually using the |
| ||
| receiver setup on page 43. |
| ||
|
|
| Español | |
15
En
