2.2.1.3 LED Definition

The LEDs indicate the status of 10/100 Mbps Ethernet ports, 1000Base-T ports, Temp. Fan and Power.

LEDStateIndication

System

 

 

 

 

 

Power

On

Switch is receiving power.

 

 

 

SNMP

On

SNMP agent operational.

 

 

 

Console

On

RS-232 Console interface is operating

 

 

 

Fan*1

On

One of the fans is failed and standby fan is running

Temp*2

On

The internal temperature is equal to or higher than 60 degree C

10BaseT/100BaseTX Ports

 

 

 

 

LNK

On

Port has established a valid network connection

 

 

 

Mode*3

 

 

COL

On

Collision occurs on the port

 

 

 

ACT

On

Traffic is passing through the port

 

 

 

FDX

On

Been set to full duplex

 

 

 

100M

On

Connected on 100M speed

 

 

 

1000BaseT Ports

 

 

 

 

 

LNK

On

Port has established a valid network connection

 

 

 

ACT

On

Traffic is passing through the port

 

 

 

*1 There are two 4-inch fans and one 2-inch fan in the unit. Normally, one of the 4-inch fans and 2-inch fan is running. Another 4-inch fan is standby and not working. Once one of the two running fans is failed, the standby fan will be drove to run and the Fan LED will light on.

*2 When the internal temperature is equal to or higher than 60 degree C, the standby fan will be drove to run and the Temp LED will light on. Once the temperature is equal to or higher than 70 degree C, the buzzer will sound. You can press the buzzer On/Off button to turn off the buzzer.

*3 Use the Mode button to select LED display mode.

2.2.2 Front Panel of WGS3-404

The front panel of the WGS3-404 has 4 RJ-45 ports for 10/100/1000 Mbps in the middle. The port status LEDs are indicated at the left. The expansion modules are situated at the right.

2.2.2.1 Front Panel Description

LEDs

System LEDs

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

10/100/1000 Mbps ports

 

 

 

 

 

 

 

 

Expansion Ports

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

WGS3 Layer 3 Switch User’s Manual

- 5 -