Powerware 9315 Remote Monitor Panel

Powerware 9315 (200 kVA---300kVA) Opera tion

164201036 Rev.D 041500

Remote Monitor Panel

As an option, you can installRemote Monitor Panels (RMPs) to monitor the

operation of the UPS system from virtually any location within your fa cility,up to

500 feet from the UPS. Each RMP contains backlit status indicators and a local

horn. You can flush-mount or surface-mount an RMP on a deskto p, wall, or

wherever you have a serial interface line. A maximum of two monitoring

accessories (RMPs, Relay Interface Modules (RIMs), or Supervisory Contact

Modules (SCMs)) can be installed. See Table 1 for the number of accessories

permitted. Figure 20 s hows an RMP.

Figure 20. Remote Monitor Panel

Table1. Optional Monitoring Accessories

Number and Type of Accessories Permitted

Remote Monitor Panel Relay Interface Module Super visory Contact Module

2 — —

— 2 —

— — 2

1 1 —

1 — 1

— 1 1

Contents

Main Page Table of Contents 1 2 3 4 5 6 7 8 9 10 Page List of Figures Page Introduction Using This Manual For More Information Getting Help Getting Started Looking Inside the UPS UPS Standard Features Monitor Panel Control Panel Communication Panel Input Filter Options and Accessories Battery External Battery Disconnect Power DistributionModule Upgrade Capability Safety Considerations Symbols, Controls, and Indicators Understanding UPS Operation Normal Mode Bypass Mode Battery Mode Monitoring and Controlling UPS Operation CONTROL PANEL MONITOR PANE L Page Starting and Stopping the UPS Using the Control Panel 7. To Place the UPS in Normal Mode: 1. 2. 3. 4. 5. 6. To Shut Down the UPS from Normal Mode: To Start the UPS in Bypass Mode: To Shut Down Power to the Critical Load While in Bypass Mode: Page Using the Monitor Panel Using the LCD Screen A B C D E Using the Pushbuttons Adjusting the Contrast Using the Load Off Pushbutton Reading the Status Indicators Normal Battery Bypass Notice Using the Menu Options 24 Figure 11. Load Amps Meters Screen Page Page 27 Figure 14. Unit Statistics Screen Page Page Page 31 Using Features and Options RS232 Building Alarm Monitoring TB1 TB2 Summary Alarm Contacts Remote Monitor Panel Table1. Optional Monitoring Accessories The RMP contains a local horn and the following backlit status indicators: Battery Cabinets External Battery Disconnect Relay Interface Module Supervisory Contact Module Page Serial Communications Locating the Communications Panel Connecting Equipment to a Serial Port PORT 1 (DE--9) Table 2. Pin Assignm ents for Port 1 (DE--- 9) PORT 2 (DB--25) Table 3. Pin Assignm ents for Port 2 (DB--- 25) Pin # Symbol Description Comments 3 5 Configuring the Serial Ports Tab le 4. Mode Rate Data/Stop Handshaking Disabled (No Handshaking) XON/XOFF Save Ter m in al M o de Printing Selected Information Entire Log (Ctrl + P) Meters Printout (Ctrl + M) + System Information Printout (Ctrl + A) Battery Test Printout(Ctrl + B) System Configuration System Configuration Mode Main Menu Program Building Alarms Enable/Disable Default Functions Customize Alarm Messages Program UnitName Adjust Output Voltage Change Password Battery Test Setup Modify Low Battery Time Calibration Mode Computer Mode Remote Monitor Mode Page Remote Notification Remote Notification Features Description of Operation Housekeeping Hardware Requirements Configuring the Modem Basic Modem Configuration Configuring the Modem to Call a Remote Computer Configuring the Modem to Call a Numeric Pager Configuring the Modem to Answer Incoming Calls Final Modem Configuration UPS Setup Configuration User-Selected Events Page Page Maintaining the UPS System Important Safety Instructions Page Performing Preventive Maintenance Maintenance Training Page Product Specifications System Input System Output Environmental Specifications Battery Specifications Page Responding to System Events System Event Horns System Event Lights System Event Messages Page Page Using the LOAD OFF Pushbutton To Use the LOAD OFF Pushbutton 1. 2. Resetting the UPS System after Load Off