Port Statistics Data Window Entries | Q-Logic 59022-03 D specification

5 – Managing Ports
Displaying Port Information


	Table 5-5. Port Statistics Data Window Entries (Continued)

	Entry		Description

	Class 3 Toss Count		Number of class 2 and class 3 sequences that were discarded
			by this port. A sequence can be discarded because of
			detection of a missing frame (based on SEQ_CNT), detection
			of an E_D_TOV timeout, receiving a reject frame, receiving
			frames for a stopped sequence, or other causes.
	FReject Count		Number of frames, from devices, that have been rejected.
			Frames can be rejected for any of a large number of reasons.
	FBusy Count		Number of class 2 and class 3 fabric busy (F_BSY) frames
			generated by this port in response to incoming frames. This
			usually indicates a busy condition on the fabric or N_port that
			is preventing delivery of this frame.
	Link Failures		Number of optical link failures detected by this port. A link
			failure is a loss of synchronization for a period of time greater
			than the value of R_T_TOV or by loss of signal while not in the
			offline state. A loss of signal causes the switch to attempt to
			re-establish the link. If the link is not re-established by the time
			specified by R_T_TOV, a link failure is counted. A link reset is
			performed after a link failure.
	Primitive Sequence		Number of bad primitives received by the port.
	Errors
	Rx Link Resets		Number of link reset primatives received from an attached
			device.
	Tx Link Resets		Number of link reset primatives sent from this port to an
			attached port.
	Rx Offline Sequences		Number of offline sequence primitives received by the port.
	Tx Offline Sequences		Number of offline primitives transmitted by the port.
	Total Errors		Total number of primitive and non-primitive port link errors.
	Total Tx Frames		Total number of frames transmitted by the port.
	Total Rx Frames		Total number of frames received by the port.
	Total Tx Words		Total number of words transmitted by the port.
	Total Rx Words		Total number of words received by the port.
	Total Link Resets		Number of link-reset primitives the transmitted by the port.
	Total Offline		Total number of offline sequences transmitted and received by
	Sequences		the port.

5-6	59022-03 D

Image 82

Q-Logic 59022-03 D manual Port Statistics Data Window Entries

Contents

SANbox2 Switch Management User’s Guide SANbox2 Switch Management User’s Guide Document Revision History Table of Contents Section Managing Fabrics 11.2 Section Managing Switches Appendix a Command Line Interface Section Managing Ports Glossary Index Figures Tables Port Statistics Data Window Entries SANbox2 Switch Management User’s Guide 59022-03 D Intended Audience Related Materials Training Technical SupportAvailability Contact Information Installing SANbox Manager Management Workstation Requirements For Windows Press the Enter key Enter the following command For Linux For Solaris Starting SANbox Manager SANbox Manager Window Load Default Fabric View File Window Exiting SANbox Manager Save Current Fabric View Window Uninstalling SANbox Manager Changing Default File Password Setting Preferences Preferences Window Using Online Help Viewing Software Version and Copyright Information Topology Display SANbox Manager User InterfaceFaceplate Display Some menu selections have shortcut keys as shown in Table Menu BarMenu Shortcut Keys Tool Bar Tool Bar buttons Fabric Tree Fabric Tree Graphic Window Working Status IndicatorData Window and Tabs Using the Topology Display Switch and Link Status Moving a Switch in the Display Working with Switches and LinksSelecting Switches and Links Opening the Faceplate Display and Popup Menus Using the Faceplate Display Topology Data Windows Working with Ports Port Views and StatusSelecting Ports Opening Popup Menus Faceplate Data Windows Security User AuthenticationFabric Security Managing the Fabric Database Adding a Fabric Saving a Fabric View File Removing a FabricOpening a Fabric View File Rediscovering a Fabric Adding a New Switch to a Fabric Deleting Switches and Links Replacing a Failed Switch in a FabricDisplaying Fabric Information Topology Display Switch and Status Icons Fabric Status Switch communication interrupted Red Active Zone Set Data Window Active Zone Set Data Window Zoning a Fabric Zoning Concepts Zones Soft Zones Virtual Private Fabric Hard Zones Access Control List Hard ZonesAliases Zone Sets Zoning Database Zoning Configuration Default Visibility Merge ModeAuto Save Using the Zoning Config Window Restoring Default Zoning Merging Fabrics and Zoning Zone Merge Failure RecoveryZone Merge Failure Using the Edit Zoning Window Edit Zoning Window Edit Zoning Window Tool Bar Buttons Managing Zone Sets Creating a Zone Set Activating and Deactivating a Zone Set Removing a Zone from a Zone Set or from All Zone Sets Copying a Zone to a Zone SetRemoving a Zone Set Managing Zones Removing All Zoning DefinitionsCreating a Zone in a Zone Set Adding Zone Members Removing a Zone from a Zone Set Renaming a Zone or a Zone SetRemoving a Zone Member Removing a Zone from All Zone Sets Managing Aliases Changing Zone TypesCreating an Alias Adding a Member to an Alias Removing an Alias from All Zones Managing Switches Displaying Switch Information Displaying Hardware Status Faceplate Display Name Server Data Window Name Server Data Window Entries Switch Data Window Switch Data Window Entries Port Statistics Data Window Port Information Data Window Configured Zonesets Data Window Alarm Log Data Window Resetting a Switch Exporting Alarm Log Information to a FilePaging a Switch Configuring a Switch Switch Administrative States Switch ConfigurationSwitch Administrative States Chassis Name Domain ID Broadcast Support Timeout Values Timeout Values Network Configuration Network Properties Window IP Configuration IP Configuration Parameters Snmp Configuration Parameters Snmp ConfigurationRemote Logging Configuration Restore Snmp Trap ConfigurationConfiguration Backup Snmp Trap Configuration Parameters Reinitializing the Configuration File System Archiving a Switch Restoring a Switch Loading Firmware Restoring the Factory Default Configuration Factory Default Configuration SettingsPage Managing Ports Displaying Port Information Displaying Port Modes Monitoring Port StatusPort Modes Port Operational States Displaying Port Operational StatesDisplaying Port Speeds Port Speeds Transceiver Media View Displaying Tranceiver Media StatusPort Statistics Data Window Entries Port Statistics Data Window Entries Port Statistics Data Window Entries Port Info Data Window Entries Configuring Ports Port Properties Window Port Administrative States Changing Port Administrative StatesChanging Port Speeds Changing Port Modes Stream Guard Changing TL ModesChanging Buffer-to-Buffer Credits Extending Port Credits Extended Credits Window Resetting a Port Testing Ports Managing Ports Testing Ports Command Line Interface Logging On to a Switch Command syntax is as follows Command SyntaxCommand keyword keyword value Commands Table A-1. Commands Listed by Authority Level Cancel Admin CommandAuthority Admin Keywords start Alias Command Authority Admin Syntax alias Remove alias members Rename aliasold aliasnew Keywords activate config Config CommandSyntax config Edit config Save config Authority Admin Syntax date Date CommandKeywords MMDDhhmmCCYY Syntax Fallback CommandAuthority Examples Command Help CommandHelp command keyword Keywords User History CommandHistory Keywords cleanup Image CommandAuthority Admin Syntax image cleanup Unpack file Lip portnumber Lip CommandPortnumber Passwd accountname Passwd CommandAdmin Accountname Authority User Syntax ps Ps CommandExamples The following is an example of the Ps command Displays current system process information Closes the Telnet session Quit CommandAuthority User Syntax quit, exit, or logout Authority Admin Syntax reset config factory Reset CommandKeywords config Table A-2. Switch Configuration Defaults Table A-3. Port Configuration Defaults Table A-3. Port Configuration Defaults Table A-5. System Configuration Defaults Syntax set alarm clear Set Alarm Clear CommandClears the log list of alarms Examples The following example clears the list of alarms Set beacon state Set Beacon CommandState Table A-6. Set Config Port Parameters Set Config CommandSet config Port portnumber Use Arbff instead of idles on loop Table A-7. Set Config Switch Parameters Table A-8. Set Config Zoning Parameters With formatting and current values will follow Following is an example of the Set Config Switch command Mfstov Following is an example of the Set Config Zoning command Archive Set Log CommandSet log Clear Port ports Level levelSave Start Log Stop commandStop Set Port Command Table A-9. Snmp Configuration Settings Set Setup CommandSet setup Snmp System Table A-10. System Configuration Settings Contact Following is an example of the Set Setup System command Set Switch Command Set switch Show Command Keywords about Perf option Log optionTable A-11. Show Port Parameters LIP Alpd Alps Topology Setup optionSteering domainid Users Following is an example of the Show Domains command Following is an example of the Show Fabric command Following is an example of the Show Setup Snmp command Following is an example of the Show Topology command NL 20000020372b05c9 NL 20000020372b095e NL 20000020372b0920 Following is an example of the Show Port command LIPF8F7 Following is an example of the Show Switch command Displays configuration parameters for the switch Show Config CommandShow config Displays zoning configuration parameters for the switch Following is an example of the Show Config Switch command Following is an example of the Show Config Zoning command Show Log Command Keywords component Following is an example of the Show Log Options command Following is an example of the Show Log command Syntax show perf Show Perf CommandDisplays performance data for all ports Keywords byte bytes/sec Show setup Show Setup CommandDisplays the current Snmp and system settings Displays the current Snmp settings Following is an example of the Show Setup System command Shutdown Command Syntax shutdown Syntax test portnumber testtype Keywords portnumber Test CommandTesttype Set port x state online Examples The following is an example of the Uptime command Uptime CommandAuthority User Syntax uptime Add User CommandAccounts Delete accountname Following is an example of the User Delete command Following is an example of the User List command Examples The following is an example of the Whoami command Whoami CommandAuthority User Syntax whoami Zone Command Syntax zone Rename zoneold zonenew Members zoneRemove zone members Type zone zonetype Following is an example of the Zone Members command Following is an example of the Zone Zonesets command Zoneset Command Keywords active Rename zonesetold zonesetnew Remove zoneset zonelistZones zoneset Edit Zoning CommandOpens a Zoning Edit session Following is an example of the Zoning List command Configured Zoning Information Command Line Interface Zoning Command 59022-03 D Class 3 Service BootPClass 2 Service Fabric Management Switch Over Temperature LED Input Power LEDOutput Power LED Power On Self Test Post Target Small Form FactorSmall Form-Factor Pluggable Worldwide Name WWN SANbox2 Switch Management User’s Guide 59022-03 D Glossary-4 Index Index-2 59022-03 D 59022-03 D Index-3 Index-4 59022-03 D