Speciﬁcations | Quantum Instruments Cascade Laser Starter Kit

Starter Kit Instruction Manual

Description

14

4.3.3Speciﬁcations

Far ﬁeld elliptical (FWHM):

Vertical: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60◦

Horizontal: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40◦

Operating temperature:

Might vary for each laser, but generally located in the range from -30 ◦C to +30 ◦C

Caution !

Before operating the laser at diﬀerent temperature than speciﬁed in the datasheet, please contact Alpes Lasers SA or a representative. Damages resulting from a non-respect of temperature operat- ing range without approval from Alpes Lasers SA will led to a loss of warranty.

Submount size :

ST mounting: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 x 7 x 2 mm3

NS mounting: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 x 7 x 2.5(top of the ceramic pads) mm3

Typical laser position:

Over the submount, centered laterally: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.2 mm

Inside the sub-mount top surface: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.03 mm

Laser emitting facet: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.005 - 0.030 x 0.004 mm2

Image 15

Quantum Instruments Cascade Laser Starter Kit manual Speciﬁcations

Contents

Instructions Manual Web version Quantum Cascade Laser Starter Kit Contents Use InstallationTroubleshooting Maintenance Overview Appendix Manufacturer IdentiﬁcationDocument Limited waranty Compliance GeneralChapter overview Generalities Personnel GlossaryPersons Product Description style Commands styleProcedure style Typographic conventions Possible cause ProblemProcedure eﬀects style See page x-y Troubleshooting stylePage Introduction Safety InstructionsImportance of safety instructions Non-compliance with the safety regulations General safety instructions Environmental conditionsCompliance and informa- tion System Composition Description Geometry of QC lasers DFB and FP Quantum Cascade LasersIf no conﬁguration is speciﬁed, the DN pad is used Description Speciﬁcations Electrical model Electrical model characteristics LLH100 external view description Laboratory Laser HousingLLH100 LLH100 internal view Laboratory Laser Housing internal view Thermo-Electric Cooler TEC and PT100 connections Speciﬁcations of the Peltier connector Measurement connection Speciﬁcations of the measurement connector QCL pulser switching unit front and rear view QCL pulser switching unitLDD100 Timing data QCL pulse switching measuring unitGeneralities Measured voltages Duty cycle calculation Laser peak current Laser peak voltage Average dissipationAccuracy considerations QCL pulser timing unit TPG128 Trigger and logic output signals Ω TTL driver circuit Peltier and PT100 connections QCL temperature controllerTCU151 Standard items InstallationChapter overview Packing list General Setting the appropriate AC voltage on TCU151 Procedure110-120V, 60Hz USA 220-240V, 50Hz Europe Before beginning Installing the starter Kit Connecting Starter Kit QCL pulse timing unit com- mand description Use TCU151 temperature controler front panel TCU151 command description Laser utilisation OverviewProceedings Starting the TPG128 Interlock utilisation Procedure Interlock utilisation Principle TroubleshootingPower supply reaches max cur- rent for a very low voltage DC power supply is not ﬂoating There is no contact with the laser Laser draws current but gives no lightLaser does not draw current QCL laser is not used with the LLH and is grounded Maintenance How to remove the covers of TCU151 and TPG128Overview Quantum Cascade Laser replace Ment Replacement procedures + LLH100 connection Facet on the case, it is extremely fragile Exchanging the laser QCL UP and DN position Exchange Humidity If the ambient atmosphere is humid this is Needed material TCU151 temperature con Troller interlock settingProcedure interlock setting Before beggining interlock set Ting Generalities Calibaration proceduresProcedure calibration 1 TPG128 calibration TPG128 main board TPG128 main board Procedure +5V/-5V power supply check 2 TCU151 temperature controller calibration = 1.22 to Sensing level and range adjustement Temperature Reference oﬀset adjustment LCD screen should display 1.00 a Current/Voltage ratio adjustmentSetting Oscillator check Starting the power section of the instru Ment 7V = 70 C If needed, adjust it with the trimmer P92 Current adjustment → Value displayed ≤ 1A→ Value displayed should tend to the deﬁned value → The red LED 1 should turn oﬀ Miscellaneous functions testing Temperature Limit testing→ The temperature displayed 2 should be 035 C Threshold on Frequency modulation technique Tildas Application notesDetection techniques Direct absorption Photoacoustic technique Photoacoustic detection Appendix Bias Circut Bias-TGeneral Utilisation What has to be kept in mind before use? Avoid reverse polarity on the input Current and voltage ranges of the Bias-T cir- cuit Unpacking instructions for NS submounts Unpacking NS laser from its transportation box