Needed material | Quantum Instruments Cascade Laser Starter Kit

Starter Kit Instruction Manual

Maintenance

42

8.3

TCU151 temperature con-

troller interlock setting

8.3.1

Generalities

The interlock is located on the main board.

Note: By default, the interlock is set to NC (Nor-

mally Close) contact.

8.3.2 Before beggining interlock set-

ting

1

2

[1] Switch the instrument OFF.

[2] Unplug the power cord.

[3] Remove the cover (1) to acces the main

board (2).

Alar

e

m

mp

Reset

Se

Real

er151

8.3.3

Needed material

Exter

ttin

C Re

e

Con

gC

alI

nal

tro

Setting+I

lle

Int

r

Se

er

nal

ttin

g−I

• 1 set of screwdriver.

+

−

• 1 tweezer.

8.3.4 Procedure interlock setting	Fig.31: Opening the TCU151 cover

To set the type of interlock, proceed as follows:

[1]Locate the J9 Interlock connector.

[2]Place the associated jumper according to the type of desired interlock.

Note: The common pin is on the center (4) and by placing the jumper on a side deﬁnes the interlock type as:

–for a NC contact: jumper on pins (4) and

(5)

–for a NO contact: jumper on pins (3) and (4)

3

4

5

Fig.32: J9 Interlock connector

Image 43

Quantum Instruments Cascade Laser Starter Kit manual TCU151 temperature con Troller interlock setting, Needed material

Contents

Instructions Manual Web version Quantum Cascade Laser Starter Kit Contents Use InstallationTroubleshooting Maintenance Overview Appendix Manufacturer IdentiﬁcationDocument Limited waranty Compliance GeneralChapter overview Generalities Personnel GlossaryPersons Product Description style Commands styleProcedure style Typographic conventions Possible cause ProblemProcedure eﬀects style See page x-y Troubleshooting stylePage Introduction Safety InstructionsImportance of safety instructions Non-compliance with the safety regulations Environmental conditions General safety instructionsCompliance and informa- tion System Composition Description Geometry of QC lasers DFB and FP Quantum Cascade LasersIf no conﬁguration is speciﬁed, the DN pad is used Description Speciﬁcations Electrical model Electrical model characteristics LLH100 external view description Laboratory Laser HousingLLH100 LLH100 internal view Laboratory Laser Housing internal view Thermo-Electric Cooler TEC and PT100 connections Speciﬁcations of the Peltier connector Measurement connection Speciﬁcations of the measurement connector QCL pulser switching unit front and rear view QCL pulser switching unitLDD100 Timing data QCL pulse switching measuring unitGeneralities Measured voltages Duty cycle calculation Laser peak current Average dissipation Laser peak voltageAccuracy considerations QCL pulser timing unit TPG128 Trigger and logic output signals Ω TTL driver circuit Peltier and PT100 connections QCL temperature controllerTCU151 Standard items InstallationChapter overview Packing list General Procedure Setting the appropriate AC voltage on TCU151110-120V, 60Hz USA 220-240V, 50Hz Europe Before beginning Installing the starter Kit Connecting Starter Kit QCL pulse timing unit com- mand description Use TCU151 temperature controler front panel TCU151 command description Overview Laser utilisationProceedings Starting the TPG128 Interlock utilisation Procedure Interlock utilisation Principle TroubleshootingPower supply reaches max cur- rent for a very low voltage DC power supply is not ﬂoating There is no contact with the laser Laser draws current but gives no lightLaser does not draw current QCL laser is not used with the LLH and is grounded How to remove the covers of TCU151 and TPG128 MaintenanceOverview Quantum Cascade Laser replace Ment Replacement procedures + LLH100 connection Facet on the case, it is extremely fragile Exchanging the laser QCL UP and DN position Exchange Humidity If the ambient atmosphere is humid this is Needed material TCU151 temperature con Troller interlock settingProcedure interlock setting Before beggining interlock set Ting Generalities Calibaration proceduresProcedure calibration 1 TPG128 calibration TPG128 main board TPG128 main board Procedure +5V/-5V power supply check 2 TCU151 temperature controller calibration = 1.22 to Sensing level and range adjustement Temperature Reference oﬀset adjustment LCD screen should display 1.00 a Current/Voltage ratio adjustmentSetting Oscillator check Starting the power section of the instru Ment 7V = 70 C If needed, adjust it with the trimmer P92 → Value displayed ≤ 1A Current adjustment→ Value displayed should tend to the deﬁned value → The red LED 1 should turn oﬀ Miscellaneous functions testing Temperature Limit testing→ The temperature displayed 2 should be 035 C Threshold on Frequency modulation technique Tildas Application notesDetection techniques Direct absorption Photoacoustic technique Photoacoustic detection Bias Circut Bias-T AppendixGeneral Utilisation What has to be kept in mind before use? Avoid reverse polarity on the input Current and voltage ranges of the Bias-T cir- cuit Unpacking instructions for NS submounts Unpacking NS laser from its transportation box