Quantum Instruments Cascade Laser Starter Kit Identication

Chapter 1

Identiﬁcation

1.1 Document

Quantum Cascade Laser Starter Kit Instructions Manual.

Web Version3.1 02.0 7

Manufacturer

Alpes Lasers SA

1-3 Passage Max-Meuron

CP 1766

CH-2001 Neuchˆatel

Tel. ++4132 729951 0

Fax. ++41 32 7213619

http://www.alpeslasers.ch

info@alpeslasers.ch

1.2 L imited waranty

Alpes Lasers SA will accept no responsibility for problems arising out of incorrect use of the instrument.

Under no circumstances will Alpes Lasers SA be held liable for any damage, or ﬁnancial loss imputable

to the instrument.

Copyrightc



The reproduction, even partially, of this document is forbidden. No part can be copied

in any form, and cannot be used, edited nor transmitted by any electronic means

(photocopy, photography, magnetic supports or other recording processes), without the

written authorization of Alpes Lasers SA. All rights and particularly reproduction,

translation, edition, distribution and also industrial property and recording are reserved.

Printed in Switzerland

4

Contents

Main Contents Page Page Chapter 1 Identication 1.1 Document 1.2 L imited waranty Chapter 2 General 2.1 Chapter overview 2.2 Generalities 2.3 Compliance 2.3.1 Laser compliance 2.4 Glossary 2.5 Typ ographic conventions Problem Page Chapter 3 Safety Instructions 3.1 Chapter overview 3.2 Introduction 3.2.1 Principle 3.2.2 Importance of safety instructions 3.3 G eneralsafety instructions 3.4 Environmental conditions 3.5 Compliance and informa- tion Chapter 4 Description 4.1 Chapter overview 4.2 S ystem Composition 4.3 DF B and FP QuantumCascade Lasers 4.3.1 Description 4.3.2 Geometry of QC lasers If no conguration is specied, the DN pad is used. 4.3.3 Specications 4.3.4 Electrical model 4.4 L aboratory Laser Housing(LLH100) Page 4.4.3 Thermo-Electric Cooler (TEC) and PT100 connections 4.4.4 Measurement connection 4.5 QCL p ulserswitching unit(LDD100) 4.5.1 Description 4.5.2 Specications 4.6 QCL pulse switching measuring unit 4.6.1 Generalities 4.6.2 Measured voltages 4.6.3 Timing data 4.6.4 Laser peak current 4.6.5 Laser peak voltage 4.6.6 Average dissipation 4.6.7 Accuracy considerations 4.7 QCL pulser timing unit (TPG128) 4.7.1 Description 4.7.2 Specications 4.8 QCL temp erature controller(TCU151) 4.8.1 Description 4.8.2 Specications 4.8.3 Peltier and PT100 connections Chapter 5 Installation 5.1 Chapter overview 5.2 General 5.3 Packing list 5.3.1 Standard items 5.4 S etting the appropriate AC voltage on TCU151 5.4.1 Procedure 5.5 In stalling the starter Kit 5.5.1 Before beginning 5.5.2 Procedure Page Chapter 6 Use 6.1 Chapter overview 6.2 QCL pulse timing unit com- mand description 6.3 T CU151command description 6.4 L aser utilisation 6.4.1 Overview 6.4.2 Proceedings Page 6.5 Interlock utilisation 6.5.1 Before beginning 6.5.2 Procedure Interlock utilisation Chapter 7 Troubleshooting 7.1 Chapter overview 7.2 Principle The power supply reaches max cur- rent for a very low voltage Laser draws current but gives no light The laser does not draw current Chapter 8 Maintenance 8.1 Overview 8.1.1 How to remove the covers of TCU151 and TPG128 8.2 Replacement procedures 8.2.1 Quantum Cascade Laser replace- ment Page 8.2.2 QCL UP and DN p osition exchange Page 8.3 T CU151 temperature con- troller interlock setting 8.3.1 Generalities 8.3.2 Before beggining interlock set- ting 8.3.3 Needed material 8.3.4 Procedure interlock setting 8.4 Calibaration pro cedures 8.4.1 TPG128 calibration Page Page 8.4.2 TCU151 temperature controller calibration Page Page Page Page Page Page Chapter 9 Application notes 9.1 Detection techniques 9.1.1 Direct absorption 9.1.2 Frequency modulation technique (TILDAS) 9.1.3 Photoacoustic detection Chapter 10 Appendix 10.1 Bias Circut (Bias-T) 10.1.1 General 10.1.2 Description 10.1.3 Specications 10.1.4 Utilisation