Using Navionics Nav-Chart cards, 128 nm | Raymarine 420D specification

2-8	RayChart 420/420D Chartplotter

Chart Boundary - Indicates further detail is available inside. Shown when using Navionics® Nav-Chart card.

128 nm	CSR 48°30.367'N			BRG	231°T
128 nm	POS	1°35.636'W		RNG	40.91nm
EXETER
TOPSHAM
TEIGNMOUTH
	EXMOUTH
ENPORT	TORQUAY		PORTLAND		ISLE O
PLYMOUTH	DARTMOUTH		HARBOUR
SALCOMBE
			CAP DE
			LA HAGUE
			ALDERNEY
		GUERNSEY
			JERSEY		PORTB
					PORTB
FIND SHIP	ROUTES		WAYPOINTS
					D4705_1

4.If no further chart detail is available then, when you press the bottom of the RANGE key, the result depends upon whether Plotter Mode is on or off :

•If Plotter Mode is Off, the unit beeps three times and the chart scale remains unchanged, indicating the smallest chart scale is displayed.

•If Plotter Mode is On, the scale is decreased. The vessel, waypoints, routes and tracklines are displayed without cartography.

The chart information is restored when you return to a chart scale for which the information is available.

To zoom out to a smaller-scale (less detailed) chart, press the top of the ‰RANGE key as many times as required.

2.5 Using Navionics Nav-Chart cards

The chartplotter has a built-in world map that can be used for route planning. Most areas (these are shown with chart box boundaries) are covered at a range of approximately 64nm as shown on the Status Bar at the top of the screen. Note: To ensure maximum detail for the built-in world map, two versions are available covering the Americas and the Rest of the World.

To use the chartplotter as a navigation aid, charts with detailed information for the area you wish to navigate are required. The charts are available on Navionics Nav-Chart cards, each of which can store as many as 20 charts in an electronic format, depending upon its memory storage capacity.

A Nav-Chart card provides an appropriate level of detail for a given geographic area and scale; this data can be displayed down to a range of 1/8 nm on the screen (height) if the data is available.

Image 27

Raymarine 420D manual Using Navionics Nav-Chart cards, 128 nm

Contents

Distributed by Raychart 420/ 420D Chartplotter Page Safety Notices RayChart 420 and 420D Chartplotter Owner’s Handbook United States Warranty PrefaceEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Overview IntroductionHow this Handbook is organised Chartplotter display GeneralDisplay functions Display options Operating controls 128 nm Trackpad and cursor Function bar Dedicated keys Database lists Pop-up menus Getting started Conventions usedSimulator Switching on/off Chart simulator Controlling the display Selecting the display mode Time 1234 Date 26/01/99 Using Find Ship Moving around the chart Status Bar Chart range Changing the chart scale 128 nm Using Navionics Nav-Chart cards Inserting a Nav-Chart card Removing a Nav-Chart card Displaying the chart dataDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Introduction SafetyOperation Working with waypoints Placing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Moving a waypoint Erasing a waypoint Working with routes Creating a new route Saving the Current Route Retrieving a route from the database Clearing the current route from the screen Displaying route leg and waypoint information Erasing or renaming a routeEditing a route To add a waypoint to the end of a route Inserting/deleting waypoints in a route Following routes and going to target points Reverse a route Follow a route Target point arrival Alter a routeJoin a route Advance to a waypoint Restart Cross Track Error XTE Go to a waypoint Going to an individual target Go to a port Go to cursor Stop follow or stop goto Changing the display mode CDI display BDI display Waypoint data BRG 234 T RNG 12.4 nm Navigation data COG 230 T SOG 6.8 Kts Time/Date Data Time Date 26/01/99 Transferring waypoints and routes Displayed waypointsManaging database lists WPT/ROUTE Transfer Using tracks Setting Setting up a track Man Overboard MOB Clearing the current trackSmartRoute‰ Range key operates normally to change chart scale Alarms System set up parameters Setting up the chartplotter Menu Options Factory New Default Setting Variation Bearing modeKey beep Units Simulated COG Time offsetLanguage Simulated SOG Chart set up parameters Parameter Options Factory New Default Setting Show waypoints Plotter modeWaypoint symbol Orientation Screen amplifier Anchor alarmXTE alarm Chart text Depth contours 20M Chart boundariesDepth contours 5M Depth contours 10M GPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter EMC Installation Guidelines Installation Unpacking and inspecting the components Suppression ferritesConnections to other equipment Selecting the best location LocationItems Missing? Registering this Product 122 mm 4.8 Panel mounting Connecting to other equipmentMounting the chartplotter Trunnion yoke mounting D47221 Chartplotter connectors GPS connectorCabling POWER/NMEA connector Function Color System Check and Initial Switch On System Check Initial Switch On Checking the Chartplotter Operation RayChart 420/420D Chartplotter Routine checks Maintenance & fault findingMaintenance Servicing and Safety Two types of reset are available for the Chartplotter Resetting the system Fault finding Problem solving Worldwide support How to contact Raytheon Marine USFor accessories and parts For product repair and service How to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Y2K Appendix a Specification RayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 COG Appendix C List of abbreviations RayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Warranty Limitations Limited Warranty Certificate United States of America Factory Service Centers