Location, Items Missing?, Registering this Product | Raymarine 420D

Chapter 5: Installation	5-3

Items Missing?

If any of the above items are missing or damaged, please contact your Raytheon dealer or our Product Support Department to obtain replacement parts. Please

note that missing or damaged items cannot be replaced without proof of purchase.

Registering this Product

When you have checked that you have all of the listed components, please take the time to complete the pre-paid warranty registration card. This ensures that you receive prompt and expert attention should you experience any difficulties with the product.

5.3 Location

This section provides information affecting the possible location of the unit for ease of use, access for servicing and its position relative to the power supply.

Selecting the best location

The unit can be mounted using the trunnion (yoke) bracket, or panel mounted using the optional Panel Mounting Kit.

When planning the installation of your RayChart 420, the following points should be considered to ensure reliable and trouble free operation:

•Convenience: The unit should be installed in a convenient position where it can be viewed straight on or with a viewing angle of less than 35°. You may wish to apply power, before you install the unit, to determine the best viewing angle prior to fixing. The mounting location should be easily accessible to allow operation of the front panel controls.

•Access: There must be sufficient space behind the display unit to allow cable connections to the rear panel connectors, avoiding tight bends in the cable. At least 4cm should be allowed at the right to enable chart cards to be inserted and removed.

•Interference: The selected location should be far enough away from devices that may cause interference, such as motors and generators (see the EMC guidelines earlier in this section).

•Cable runs: The unit must be located near a dc power source. The power cable supplied is 1.5m, but a longer cable can be used if required. Power must be supplied via a 1A quick blow fuse or circuit breaker. Refer to Section 5.6 Cabling.

Image 76

Raymarine 420D manual Location, Items Missing?, Registering this Product, Selecting the best location

Contents

Distributed by Raychart 420/ 420D Chartplotter Page RayChart 420 and 420D Chartplotter Owner’s Handbook Safety Notices United States Preface WarrantyEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Introduction OverviewHow this Handbook is organised General Chartplotter displayDisplay functions Operating controls Display options Trackpad and cursor 128 nm Dedicated keys Function bar Pop-up menus Database lists Conventions used Getting startedSimulator Switching on/off Chart simulator Selecting the display mode Controlling the display Time 1234 Date 26/01/99 Moving around the chart Using Find Ship Changing the chart scale Status Bar Chart range Using Navionics Nav-Chart cards 128 nm Inserting a Nav-Chart card Displaying the chart data Removing a Nav-Chart cardDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Safety OperationWorking with waypoints Introduction Placing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Erasing a waypoint Moving a waypoint Working with routes Creating a new route Saving the Current Route Clearing the current route from the screen Retrieving a route from the database Erasing or renaming a route Displaying route leg and waypoint informationEditing a route Inserting/deleting waypoints in a route To add a waypoint to the end of a route Following routes and going to target points Follow a route Reverse a route Alter a route Target point arrivalJoin a route Restart Cross Track Error XTE Advance to a waypoint Going to an individual target Go to a waypoint Go to cursor Go to a port Changing the display mode Stop follow or stop goto CDI display BDI display BRG 234 T RNG 12.4 nm Waypoint data COG 230 T SOG 6.8 Kts Navigation data Time Date 26/01/99 Time/Date Data Displayed waypoints Transferring waypoints and routesManaging database lists Using tracks WPT/ROUTE Transfer Setting up a track Setting Clearing the current track Man Overboard MOBSmartRoute‰ Alarms Range key operates normally to change chart scale Setting up the chartplotter System set up parameters Menu Options Factory New Default Setting Bearing mode Key beepUnits Variation Time offset LanguageSimulated SOG Simulated COG Chart set up parameters Parameter Options Factory New Default Setting Plotter mode Waypoint symbolOrientation Show waypoints Anchor alarm XTE alarmChart text Screen amplifier Chart boundaries Depth contours 5MDepth contours 10M Depth contours 20M GPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter Installation EMC Installation Guidelines Suppression ferrites Unpacking and inspecting the componentsConnections to other equipment Location Items Missing?Registering this Product Selecting the best location 122 mm 4.8 Connecting to other equipment Mounting the chartplotterTrunnion yoke mounting Panel mounting D47221 GPS connector Chartplotter connectorsCabling POWER/NMEA connector System Check and Initial Switch On Function Color Initial Switch On System Check Checking the Chartplotter Operation RayChart 420/420D Chartplotter Maintenance & fault finding MaintenanceServicing and Safety Routine checks Resetting the system Two types of reset are available for the Chartplotter Problem solving Fault finding How to contact Raytheon Marine US For accessories and partsFor product repair and service Worldwide support How to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Appendix a Specification Y2K RayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 Appendix C List of abbreviations COG RayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Limited Warranty Certificate Warranty Limitations Factory Service Centers United States of America