Changing the display mode, Stop follow or stop goto | Raymarine 420

3-20	RayChart 420/420D Chartplotter

3.Use trackpad up/down to select the required destination and press ENTER to start the GoTo, or CLEAR to cancel the operation.

The operation is conducted in the same manner as for GO TO PORT above.

Stop follow or stop goto

To stop following the route or target point:

‰1. Either press the GOTO key or move the cursor over the target waypoint.

2. Select the STOP GOTO or STOP FOLLOW function respectively:D4689_1STOPFOLLOW RESTART WAYPOINTXTE ADVANCERESTARTXTESTOPGOTO

D4688_1

The dotted line from your vessel to the target waypoint disappears.

3.5 Changing the display mode

Use the PAGE key to select the required display mode. Repeat presses of the PAGE key provide the following display modes:

•Set Up functions (see Chapter 4)

•Course Deviation Indicator (CDI)

•Bearing & Distance Indication (BDI)

•Waypoint data

•Navigation data

•Time/Date data

•Return to Set Up functions

Note: Press GOTO in any display mode to return to normal Chart display.

To change the display mode:

‰Note: The Set Up Function Bar remains displayed in each display mode. To remove the Set Up Function Bar, press CLEAR.

1.		Press the PAGE key to show the SET UP functions with SYSTEM SET
		UP highlighted:

		SYSTEM		CHART		TRACK		GPS
		SETUP		SETUP		SETUP		SETUP
								D4699_1
2.		Repeat Step 1 to cycle through each of the available display modes.

Image 51

Raymarine 420D manual Changing the display mode, Stop follow or stop goto

Contents

Distributed by Raychart 420/ 420D Chartplotter Page Safety Notices RayChart 420 and 420D Chartplotter Owner’s Handbook United States Warranty PrefaceEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Overview IntroductionHow this Handbook is organised Chartplotter display GeneralDisplay functions Display options Operating controls 128 nm Trackpad and cursor Function bar Dedicated keys Database lists Pop-up menus Getting started Conventions usedSimulator Switching on/off Chart simulator Controlling the display Selecting the display mode Time 1234 Date 26/01/99 Using Find Ship Moving around the chart Status Bar Chart range Changing the chart scale 128 nm Using Navionics Nav-Chart cards Inserting a Nav-Chart card Removing a Nav-Chart card Displaying the chart dataDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Introduction SafetyOperation Working with waypoints Placing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Moving a waypoint Erasing a waypoint Working with routes Creating a new route Saving the Current Route Retrieving a route from the database Clearing the current route from the screen Displaying route leg and waypoint information Erasing or renaming a routeEditing a route To add a waypoint to the end of a route Inserting/deleting waypoints in a route Following routes and going to target points Reverse a route Follow a route Target point arrival Alter a routeJoin a route Advance to a waypoint Restart Cross Track Error XTE Go to a waypoint Going to an individual target Go to a port Go to cursor Stop follow or stop goto Changing the display mode CDI display BDI display Waypoint data BRG 234 T RNG 12.4 nm Navigation data COG 230 T SOG 6.8 Kts Time/Date Data Time Date 26/01/99 Transferring waypoints and routes Displayed waypointsManaging database lists WPT/ROUTE Transfer Using tracks Setting Setting up a track Man Overboard MOB Clearing the current trackSmartRoute‰ Range key operates normally to change chart scale Alarms System set up parameters Setting up the chartplotter Menu Options Factory New Default Setting Variation Bearing modeKey beep Units Simulated COG Time offsetLanguage Simulated SOG Chart set up parameters Parameter Options Factory New Default Setting Show waypoints Plotter modeWaypoint symbol Orientation Screen amplifier Anchor alarmXTE alarm Chart text Depth contours 20M Chart boundariesDepth contours 5M Depth contours 10M GPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter EMC Installation Guidelines Installation Unpacking and inspecting the components Suppression ferritesConnections to other equipment Selecting the best location LocationItems Missing? Registering this Product 122 mm 4.8 Panel mounting Connecting to other equipmentMounting the chartplotter Trunnion yoke mounting D47221 Chartplotter connectors GPS connectorCabling POWER/NMEA connector Function Color System Check and Initial Switch On System Check Initial Switch On Checking the Chartplotter Operation RayChart 420/420D Chartplotter Routine checks Maintenance & fault findingMaintenance Servicing and Safety Two types of reset are available for the Chartplotter Resetting the system Fault finding Problem solving Worldwide support How to contact Raytheon Marine USFor accessories and parts For product repair and service How to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Y2K Appendix a Specification RayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 COG Appendix C List of abbreviations RayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Warranty Limitations Limited Warranty Certificate United States of America Factory Service Centers