System Check and Initial Switch On, Function Color | Raymarine 420D

Chapter 5: Installation	5-9

The dc power and NMEA inputs/outputs should be connected to the POWER/NMEA connector at the rear of the RayChart 420. The connector pin functions are detailed in the following table.

Function	Color

Battery negative	Black

Battery positive (10.0Vdc to 18.0Vdc)	Red

NMEA data input (+ve)	White

NMEA input (-ve) - common	Green

Not connected	Grey

NMEA data out	Yellow

Data output common	Brown

Not connected	Screen

Connect the power supply using the standard power cable supplied, as follows:

‰1. Connect the moulded power plug to the POWER/NMEA connector on the rear of the chartplotter. Run the free end back to the vessel’s distribution

panel or, if insufficient cable length to a junction box.

2.Cut the cable to length and connect the red wire, via a fuse, to the +ve battery terminal and the black wire to 0V (-ve battery terminal). Protect the circuit with a 1A quick blow fuse or circuit breaker.

3.Use a suitable junction box to connect to NMEA equipment if required.

4.Cut any unused cores short or insulate and tape back.

Note: If the power connections are accidentally reversed, the system will not function. Use a volt meter to check that the input power leads are connected with the correct polarity.

5.7 System Check and Initial Switch On

When you have installed your Chartplotter and made all the connections, you need to check your installation before using the system for navigation. If you encounter any problems, refer to Chapter 6, Maintenance and Fault Finding.

EMC Conformance

Always check the installation before going to sea to make sure that it is not affected by radio transmissions, engine starting etc.

Image 82

Raymarine 420D manual System Check and Initial Switch On, Function Color

Contents

Distributed by Raychart 420/ 420D Chartplotter Page RayChart 420 and 420D Chartplotter Owner’s Handbook Safety Notices United States Preface WarrantyEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Introduction OverviewHow this Handbook is organised General Chartplotter displayDisplay functions Operating controls Display options Trackpad and cursor 128 nm Dedicated keys Function bar Pop-up menus Database lists Conventions used Getting startedSimulator Switching on/off Chart simulator Selecting the display mode Controlling the display Time 1234 Date 26/01/99 Moving around the chart Using Find Ship Changing the chart scale Status Bar Chart range Using Navionics Nav-Chart cards 128 nm Inserting a Nav-Chart card Displaying the chart data Removing a Nav-Chart cardDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Working with waypoints SafetyOperation Introduction Placing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Erasing a waypoint Moving a waypoint Working with routes Creating a new route Saving the Current Route Clearing the current route from the screen Retrieving a route from the database Erasing or renaming a route Displaying route leg and waypoint informationEditing a route Inserting/deleting waypoints in a route To add a waypoint to the end of a route Following routes and going to target points Follow a route Reverse a route Alter a route Target point arrivalJoin a route Restart Cross Track Error XTE Advance to a waypoint Going to an individual target Go to a waypoint Go to cursor Go to a port Changing the display mode Stop follow or stop goto CDI display BDI display BRG 234 T RNG 12.4 nm Waypoint data COG 230 T SOG 6.8 Kts Navigation data Time Date 26/01/99 Time/Date Data Displayed waypoints Transferring waypoints and routesManaging database lists Using tracks WPT/ROUTE Transfer Setting up a track Setting Clearing the current track Man Overboard MOBSmartRoute‰ Alarms Range key operates normally to change chart scale Setting up the chartplotter System set up parameters Menu Options Factory New Default Setting Units Bearing modeKey beep Variation Simulated SOG Time offsetLanguage Simulated COG Chart set up parameters Parameter Options Factory New Default Setting Orientation Plotter modeWaypoint symbol Show waypoints Chart text Anchor alarmXTE alarm Screen amplifier Depth contours 10M Chart boundariesDepth contours 5M Depth contours 20M GPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter Installation EMC Installation Guidelines Suppression ferrites Unpacking and inspecting the componentsConnections to other equipment Registering this Product LocationItems Missing? Selecting the best location 122 mm 4.8 Trunnion yoke mounting Connecting to other equipmentMounting the chartplotter Panel mounting D47221 GPS connector Chartplotter connectorsCabling POWER/NMEA connector System Check and Initial Switch On Function Color Initial Switch On System Check Checking the Chartplotter Operation RayChart 420/420D Chartplotter Servicing and Safety Maintenance & fault findingMaintenance Routine checks Resetting the system Two types of reset are available for the Chartplotter Problem solving Fault finding For product repair and service How to contact Raytheon Marine USFor accessories and parts Worldwide support How to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Appendix a Specification Y2K RayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 Appendix C List of abbreviations COG RayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Limited Warranty Certificate Warranty Limitations Factory Service Centers United States of America