Inserting a Nav-Chart card | Raymarine 420D specs

Chapter 2: Getting Started	2-9

The chart scale in use is indicated in the status bar; the number represents the distance (in nautical miles) displayed from the top to the bottom of the screen.

To obtain Navionics Nav-Chart cards contact your local dealer or:

Navionics S.p.A. Via Vespucci 289 55049Viareggio, Italy

Tel: (+39) 584 961696

Fax: (+39) 584 961309

website: www.navionics.com

Inserting a Nav-Chart card

CAUTION

To prevent the ingress of water and consequent damage to the unit, always ensure that the cartridge cover is fully and properly inserted, whether or not a Nav-Chart card is inserted.

To insert a Nav-Chart card:

‰1. Check that you are using the correct Nav-Chart card for the required area.

2.Pull out the cartridge cover at the right hand side of the unit.

3.Hold the card with the title label and keyway slot towards you, and the two circular holes outermost, as shown below. Gently push the card into its slot until it clicks into position. It will only fit in the correct orientation.

4.To prevent the ingress of water, replace the cartridge cover.

D4706_1

Image 28

Raymarine 420D manual Inserting a Nav-Chart card

Contents

Distributed by Raychart 420/ 420D Chartplotter Page RayChart 420 and 420D Chartplotter Owner’s Handbook Safety Notices United States Preface WarrantyEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Introduction OverviewHow this Handbook is organised General Chartplotter displayDisplay functions Operating controls Display options Trackpad and cursor 128 nm Dedicated keys Function bar Pop-up menus Database lists Conventions used Getting startedSimulator Switching on/off Chart simulator Selecting the display mode Controlling the display Time 1234 Date 26/01/99 Moving around the chart Using Find Ship Changing the chart scale Status Bar Chart range Using Navionics Nav-Chart cards 128 nm Inserting a Nav-Chart card Displaying the chart data Removing a Nav-Chart cardDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Safety OperationWorking with waypoints Introduction Placing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Erasing a waypoint Moving a waypoint Working with routes Creating a new route Saving the Current Route Clearing the current route from the screen Retrieving a route from the database Erasing or renaming a route Displaying route leg and waypoint informationEditing a route Inserting/deleting waypoints in a route To add a waypoint to the end of a route Following routes and going to target points Follow a route Reverse a route Alter a route Target point arrivalJoin a route Restart Cross Track Error XTE Advance to a waypoint Going to an individual target Go to a waypoint Go to cursor Go to a port Changing the display mode Stop follow or stop goto CDI display BDI display BRG 234 T RNG 12.4 nm Waypoint data COG 230 T SOG 6.8 Kts Navigation data Time Date 26/01/99 Time/Date Data Displayed waypoints Transferring waypoints and routesManaging database lists Using tracks WPT/ROUTE Transfer Setting up a track Setting Clearing the current track Man Overboard MOBSmartRoute‰ Alarms Range key operates normally to change chart scale Setting up the chartplotter System set up parameters Menu Options Factory New Default Setting Bearing mode Key beepUnits Variation Time offset LanguageSimulated SOG Simulated COG Chart set up parameters Parameter Options Factory New Default Setting Plotter mode Waypoint symbolOrientation Show waypoints Anchor alarm XTE alarmChart text Screen amplifier Chart boundaries Depth contours 5MDepth contours 10M Depth contours 20M GPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter Installation EMC Installation Guidelines Suppression ferrites Unpacking and inspecting the componentsConnections to other equipment Location Items Missing?Registering this Product Selecting the best location 122 mm 4.8 Connecting to other equipment Mounting the chartplotterTrunnion yoke mounting Panel mounting D47221 GPS connector Chartplotter connectorsCabling POWER/NMEA connector System Check and Initial Switch On Function Color Initial Switch On System Check Checking the Chartplotter Operation RayChart 420/420D Chartplotter Maintenance & fault finding MaintenanceServicing and Safety Routine checks Resetting the system Two types of reset are available for the Chartplotter Problem solving Fault finding How to contact Raytheon Marine US For accessories and partsFor product repair and service Worldwide support How to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Appendix a Specification Y2K RayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 Appendix C List of abbreviations COG RayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Limited Warranty Certificate Warranty Limitations Factory Service Centers United States of America