Screen amplifier, COG vector, Arrival circle | Raymarine 420D

4-8	RayChart 420/420D Chartplotter

Autozoom will not zoom in beyond the largest cartographic scale (see also Plotter Mode). When in MOB mode, Autozoom is selected automatically and will zoom in as far as possible, irrespective of the selection of Plotter Mode.

Unless MOB is active Autozoom will not be activated if there is no cartridge or if the area being viewed is not covered by the cartridge.

Screen amplifier

Screen amplifier mode makes better use of the screen by positioning the vessel on the screen so as to increase forward visibility. The screen amplifier is only active when the cursor is ‘homed’ on the vessel.

COG vector

When ON, a vector line from the vessel is drawn in the direction of COG. This line extends to the edge of the screen. If COG is not valid, no line is drawn. The selected setting is retained when the unit switched off.

Arrival circle

The selected value is used as the arrival circle radius. When approaching the target waypoint, this is the distance at which the arrival alarm sounds. The selected setting is retained when unit switched off. Arrival criteria are met when the arrival circle is entered or a line perpendicular to the desired track and passing through the waypoint is crossed.

Anchor alarm

The selected value is used as the anchor alarm distance. If the vessel moves outside of the selected distance from its position (at the time that the alarm was enabled) the alarm sounds and an alarm message is displayed.

To silence the alarm, press any key. This removes the warning and resets the distance, ie. the alarm will not sound again unless the vessel moves the selected distance from its position (at the time that the alarm was silenced). The alarm is set to OFF on power up.

XTE alarm

The selected value is used as the cross track error limit. The alarm sounds when the cross track error exceeds the selected limit when a GOTO or a Route Follow is in progress and an alarm message is displayed.

Chart text

When ON, Chart text, eg. place names are shown on the screen. The selected setting is retained when the unit switched off.

Image 69

Raymarine 420D manual Screen amplifier, COG vector, Arrival circle, Anchor alarm, XTE alarm, Chart text

Contents

Distributed by Raychart 420/ 420D Chartplotter Page Safety Notices RayChart 420 and 420D Chartplotter Owner’s Handbook United States Warranty PrefaceEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Overview IntroductionHow this Handbook is organised Chartplotter display GeneralDisplay functions Display options Operating controls 128 nm Trackpad and cursor Function bar Dedicated keys Database lists Pop-up menus Getting started Conventions usedSimulator Switching on/off Chart simulator Controlling the display Selecting the display mode Time 1234 Date 26/01/99 Using Find Ship Moving around the chart Status Bar Chart range Changing the chart scale 128 nm Using Navionics Nav-Chart cards Inserting a Nav-Chart card Removing a Nav-Chart card Displaying the chart dataDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Operation SafetyWorking with waypoints Introduction Placing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Moving a waypoint Erasing a waypoint Working with routes Creating a new route Saving the Current Route Retrieving a route from the database Clearing the current route from the screen Displaying route leg and waypoint information Erasing or renaming a routeEditing a route To add a waypoint to the end of a route Inserting/deleting waypoints in a route Following routes and going to target points Reverse a route Follow a route Target point arrival Alter a routeJoin a route Advance to a waypoint Restart Cross Track Error XTE Go to a waypoint Going to an individual target Go to a port Go to cursor Stop follow or stop goto Changing the display mode CDI display BDI display Waypoint data BRG 234 T RNG 12.4 nm Navigation data COG 230 T SOG 6.8 Kts Time/Date Data Time Date 26/01/99 Transferring waypoints and routes Displayed waypointsManaging database lists WPT/ROUTE Transfer Using tracks Setting Setting up a track Man Overboard MOB Clearing the current trackSmartRoute‰ Range key operates normally to change chart scale Alarms System set up parameters Setting up the chartplotter Menu Options Factory New Default Setting Key beep Bearing modeUnits Variation Language Time offsetSimulated SOG Simulated COG Chart set up parameters Parameter Options Factory New Default Setting Waypoint symbol Plotter modeOrientation Show waypoints XTE alarm Anchor alarmChart text Screen amplifier Depth contours 5M Chart boundariesDepth contours 10M Depth contours 20M GPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter EMC Installation Guidelines Installation Unpacking and inspecting the components Suppression ferritesConnections to other equipment Items Missing? LocationRegistering this Product Selecting the best location 122 mm 4.8 Mounting the chartplotter Connecting to other equipmentTrunnion yoke mounting Panel mounting D47221 Chartplotter connectors GPS connectorCabling POWER/NMEA connector Function Color System Check and Initial Switch On System Check Initial Switch On Checking the Chartplotter Operation RayChart 420/420D Chartplotter Maintenance Maintenance & fault findingServicing and Safety Routine checks Two types of reset are available for the Chartplotter Resetting the system Fault finding Problem solving For accessories and parts How to contact Raytheon Marine USFor product repair and service Worldwide support How to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Y2K Appendix a Specification RayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 COG Appendix C List of abbreviations RayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Warranty Limitations Limited Warranty Certificate United States of America Factory Service Centers