D47221 | Raymarine 420D guide

5-6	RayChart 420/420D Chartplotter

The unit can be panel mounted, using the panel-mounting kit (accessory) available from your local Raytheon dealer.

Panel mount the unit as follows:

‰1. Check the selected location for the unit. A clear, flat area at least 175mm (7in) wide by 190mm (7½in) high, with at least 90mm (3½in) of clearance

behind the panel, is required.

2.Unpack the (optional) panel-mounting kit.

3.Using the supplied template, trace out the display unit cut-out and mark the drilling centres for the four securing holes outside of the cut-out area.

4.To provide start holes for removing the cut-out, drill four 10mm (3/8 in) holes in each opposing corner and four 6mm (1/4 in) holes for the two trunnion lug clearance slots in the cut-out area.

5.Using a suitable saw, cut along the inside edge of the cut-out line.

6.With the trunnion (yoke) and knobs removed, make sure that the unit fits in the cut-out area.

7.Drill out the four 5mm (3/16 in) securing holes as indicated on the template. It is recommended that a 1mm (1/16 in) pilot hole is drilled first.

8.Screw the studs into the vacant holes at the rear of the unit, hand tight only.

9.Place the gasket on the unit and slide the unit into the panel cut-out.

10.Secure the unit with the thumb nuts, hand tight only.

D4722_1

Image 79

Raymarine 420D manual D47221

Contents

Distributed by Raychart 420/ 420D Chartplotter Page Safety Notices RayChart 420 and 420D Chartplotter Owner’s Handbook United States Preface WarrantyEMC Conformance RayChart 420/420D Chartplotter Contents Join a route Advance to a waypoint Table of Contents Vii For accessories and parts Table of Contents RayChart 420/420D Introduction OverviewHow this Handbook is organised General Chartplotter displayDisplay functions Display options Operating controls 128 nm Trackpad and cursor Function bar Dedicated keys Database lists Pop-up menus Conventions used Getting startedSimulator Switching on/off Chart simulator Controlling the display Selecting the display mode Time 1234 Date 26/01/99 Using Find Ship Moving around the chart Status Bar Chart range Changing the chart scale 128 nm Using Navionics Nav-Chart cards Inserting a Nav-Chart card Displaying the chart data Removing a Nav-Chart cardDisplaying chart information To obtain port services information RayChart 420/420D Chartplotter Introduction SafetyOperation Working with waypoints Placing a waypoint Operation Selecting a waypoint Editing the waypoint details Enter Moving a waypoint Erasing a waypoint Working with routes Creating a new route Saving the Current Route Retrieving a route from the database Clearing the current route from the screen Erasing or renaming a route Displaying route leg and waypoint informationEditing a route To add a waypoint to the end of a route Inserting/deleting waypoints in a route Following routes and going to target points Reverse a route Follow a route Alter a route Target point arrivalJoin a route Advance to a waypoint Restart Cross Track Error XTE Go to a waypoint Going to an individual target Go to a port Go to cursor Stop follow or stop goto Changing the display mode CDI display BDI display Waypoint data BRG 234 T RNG 12.4 nm Navigation data COG 230 T SOG 6.8 Kts Time/Date Data Time Date 26/01/99 Displayed waypoints Transferring waypoints and routesManaging database lists WPT/ROUTE Transfer Using tracks Setting Setting up a track Clearing the current track Man Overboard MOBSmartRoute‰ Range key operates normally to change chart scale Alarms System set up parameters Setting up the chartplotter Menu Options Factory New Default Setting Variation Bearing modeKey beep Units Simulated COG Time offsetLanguage Simulated SOG Chart set up parameters Parameter Options Factory New Default Setting Show waypoints Plotter modeWaypoint symbol Orientation Screen amplifier Anchor alarmXTE alarm Chart text Depth contours 20M Chart boundariesDepth contours 5M Depth contours 10M GPS setup Setting Up the Chartplotter RayChart 420/420D Chartplotter EMC Installation Guidelines Installation Suppression ferrites Unpacking and inspecting the componentsConnections to other equipment Selecting the best location LocationItems Missing? Registering this Product 122 mm 4.8 Panel mounting Connecting to other equipmentMounting the chartplotter Trunnion yoke mounting D47221 GPS connector Chartplotter connectorsCabling POWER/NMEA connector Function Color System Check and Initial Switch On System Check Initial Switch On Checking the Chartplotter Operation RayChart 420/420D Chartplotter Routine checks Maintenance & fault findingMaintenance Servicing and Safety Two types of reset are available for the Chartplotter Resetting the system Fault finding Problem solving Worldwide support How to contact Raytheon Marine USFor accessories and parts For product repair and service How to contact Raytheon Marine Europe RayChart 420/420D Chartplotter Y2K Appendix a Specification RayChart 420/420D Chartplotter Appendix B Nmea data RayChart420 COG Appendix C List of abbreviations RayChart 420/420D Chartplotter Cut out Shaded area Only RayChart Warranty Limitations Limited Warranty Certificate United States of America Factory Service Centers