Reducing noise in the picture
Use these settings if the picture has noise due to poor reception or when playing video tapes on which the picture quality is poor.
Example: Setting “NR-3”
1.On the MAIN MENU, select “PICTURE”, then press the MENU/ENTER button.
The “PICTURE” screen appears.
2.Use the ▲ and ▼ buttons to select “NR”.
|
|
| PICTURE |
| 1 / 2 | |||
CONTRAST |
|
|
|
|
|
| ||
BRIGHTNESS |
|
|
|
|
|
| ||
SHARPNESS |
|
|
|
|
|
| ||
COLOR |
|
|
|
|
|
| ||
|
|
|
|
|
| |||
TINT |
|
|
|
|
|
| ||
PICTURE MODE |
| : | NORMAL |
| ||||
| NR | NEXT PAGE |
| : | OFF | |||
|
|
|
|
|
|
|
| |
| SEL. | ADJ. |
| EXIT | RETURN | |||
3.Use the and buttons to select
The mode switches as follows each time the or button is pressed:
→ OFF ↔
|
|
NR | : |
|
|
*If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen reappears.
Information
NR
*“NR” stands for Noise Reduction.
*This function reduces noise in the picture.
Types of noise reduction
There are three types of noise reduction. Each has a different level of noise reduction.
The effect becomes stronger as the number increases (in the order
OFF | Turns the noise reduction function off. |
Setting the color temperature
Use this procedure to set color tone produced by the plasma display.
Example: Setting “HIGH”
1.On the MAIN MENU, select “PICTURE”, then press the MENU/ENTER button.
The “PICTURE” screen appears.
2.Use the ▲ and ▼ buttons to select “COLOR TEMP.”.
3.Use the and buttons to select “HIGH”.
The mode switches as follows each time the or button is pressed:
→ LOW ↔ MID LOW ↔ MID ↔ HIGH ←
* See below to set “WHITE BALANCE”.
|
|
| PICTURE |
| 2 / 2 | |
|
| PREVIOUS PAGE |
|
|
| |
| COLOR TEMP. |
| : | HIGH | ||
|
|
|
|
|
| |
GAMMA |
| : | 2 |
| ||
LOW TONE |
| : | AUTO | |||
COLOR TUNE |
|
|
|
| ||
|
| SEL. | ADJ. |
|
| RETURN |
|
|
| EXIT | |||
*If neither the or button is pressed within 5 seconds, the current selection is set and the previous screen reappears.
Information
Setting the color temperature
LOW | Redder |
MID LOW | Slightly redder |
MID | Standard (slightly bluer) |
HIGH | Bluer |
Restoring the factory default settings
Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.
Adjusting the color to the desired level
Use this procedure to adjust the white balance for each color temperature to achieve the desired color quality.
Example: Adjusting the “GAIN RED” of “HIGH” color temperature
Set “ADVANCED OSM” to “ON” in the main menu (1/ 2), then perform the following operations.
Perform Steps
4.Press the MENU/ENTER button.
The “WHITE BALANCE” screen appears.
5.Use the ▲ and ▼ buttons to select “GAIN RED”.
WHITE BALANCE
COLOR TEMP. HIGH
GAIN RED |
|
|
GAIN GREEN |
|
|
GAIN BLUE |
|
|
BIAS RED |
|
|
BIAS GREEN |
|
|
BIAS BLUE |
|
|
RESET |
| : OFF |
SEL. | ADJ. | EXIT RETURN |
33
