Runco PL-61CX manual POWER/STANDBY indicator, Setting the picture to suit the movie, Information

POWER/STANDBY indicator

Power	POWER/	Power	Description	Turning the picture
management	STANDBY	management		back on
mode	indicator	operating status
On	Green	Not activated.	Horizontal and vertical	Picture already on.
			synchronizing signals
			are present from the
			computer.
Off	Red	Activated.	Horizontal and/or	Operate the keyboard or
			vertical synchronizing	mouse. The picture
			signals are not sent	reappears.
			from the computer.

Setting the picture to suit the movie

The film image is automatically discriminated and projected in an image mode suited to the picture. [NTSC, PAL, PAL60, 480I (60Hz), 525I (60Hz), 576I (50Hz), 625I (50Hz), 1035I (60Hz), 1080I (60Hz) only]

Example: Setting the “CINEMA MODE” to “OFF”

Set “ADVANCED OSM” to “ON” in the main menu (1/ 2), then perform the following operations.

1.On the MAIN MENU, select “OPTION2”, then press the MENU/ENTER button.

The “OPTION2” screen appears.

2.Use the ▲ and ▼ buttons to select “CINEMA MODE”.

3.To set the CINEMA MODE to “OFF” ...

Use the  and  buttons to select “OFF”.

The mode switches as follows each time the  or  button is pressed:

ON ↔ OFF

			OPTION2		2 / 3
		PREVIOUS PAGE
POWER MGT.				:	OFF
	CINEMA MODE			:	OFF
LONG LIFE
GRAY LEVEL				:	3
S1/S2				:	OFF
		NEXT PAGE
		SEL.	ADJ.		EXIT	RETURN

Information

CINEMA MODE

ON	Automatic discrimination of the
	image and projection in cinema mode.
OFF	Cinema mode does not function.

Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.

Reducing burn-in of the screen

The brightness of the screen, the position of the picture, positive/negative mode and screen wiper are adjusted to reduce burn-in of the screen.

Set “ADVANCED OSM” to “ON” in the main menu (1/ 2), then perform the following operations.

1.On the MAIN MENU, select “OPTION2”, then press the MENU/ENTER button.

The “OPTION2” screen appears.

2.Use the ▲ and ▼ buttons to select “LONG LIFE”, then press the MENU/ENTER button.

The “LONG LIFE” screen appears.

			LONG LIFE
	PLE		:	AUTO
ORBITER			:	OFF
INVERSE			:	OFF
SCREEN WIPER			:	OFF
SOFT FOCUS			:	OFF
		SEL.	ADJ.		RETURN
				EXIT

3.Set the LONG LIFE mode using ▲▼  and  buttons. See below to set PLE.

See page 42 to set ORBITER. See page 42 to set INVERSE.

See page 43 to set SCREEN WIPER. See page 44 to set SOFT FOCUS.

Information

Restoring the factory default settings

Select “ALL RESET” under the OPTION1 menu. Note that this also restores other settings to the factory defaults.

PLE (Peak Luminance Enhancement)

Use this to activate the brightness limiter.

Example: Setting “PLE” to “LOCK1”

Perform Steps 1-2 of LONG LIFE, then...

3.Use the ▲ and ▼ buttons to select “PLE”.

4.Use the  and  buttons to select “LOCK1”.

The mode switches as follows each time the  or  button is pressed:

→ AUTO ↔ LOCK1 ↔ LOCK2 ↔ LOCK3←

			LONG LIFE
	PLE		:	LOCK1
ORBITER			:	OFF
INVERSE			:	OFF
SCREEN WIPER			:	OFF
SOFT FOCUS			:	OFF
		SEL.	ADJ.		RETURN
				EXIT

41

Information

PLE settings

AUTO .............. The brightness of the screen is

adjusted automatically to suit the picture quality.