Manuals / Runco / Computer Equipment / Computer Monitor

Runco PL-61CX manual Use of Installation Remote Control

Models: PL-61CX

1 76

Page 15

Use of Installation Remote Control

The Installation remote has been included with the PL-61cx in order to allow the adjustment of size and position for HDTV signals, or any other high-resolution signal sent into the “HDTV/Computer” port on the Controller.

Do not use this remote to make color balance adjustments or any other image quality adjustments to the plasma itself. All image quality adjustments are stored in the PFP Controller, NOT in the plasma. Any adjustments made to the plasma will not be stored and will be lost when the plasma is turned off.

To adjust position or size for high-definition signals, perform the following:

1. Press PROCEED.

2. Press the DOWN ARROW twice so “SCREEN” is highlighted and press PROCEED.

3.Select either V or H POSITION, V HEIGHT or H WIDTH as desired, and press PROCEED.

4.Using the arrow buttons, adjust the position or

size as necessary.

5. When done, press EXIT several times until the menu disappears.

Page 15

Image 15

Runco PL-61CX manual Use of Installation Remote Control

Contents

OWNER’S OPERATING MANUAL PL-61cxTable of Contents OSM On Screen Menu Controls Introduction to the Runco PlasmaWall PL-61cx Plasma Display Monitor The features you’ll enjoy includeContents of the package IntroductionPrecautions Warnings and Safety PrecautionImportant Information 2. Handle the unit carefully when installing it and do not drop WHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY THREE YEAR LIMITED WARRANTYFor Plasma Display Monitors WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTYRUNCO INTERNATIONAL Attn Customer Service Department EFFECTIVE WARRANTY DATEIMPORTANT WARRANTY REGISTRATION CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICEWHAT IS NOT COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY TWO YEAR LIMITED WARRANTYFor Projectors, Video Processors and Controllers WHAT IS COVERED UNDER THE TERMS OF THIS LIMITED WARRANTYCAUTION THIS LIMITED WARRANTY ONLY COVERS RUNCO PRODUCTS PURCHASED FROM RUNCO AUTHORIZED DEALERS. ALL OTHER PRODUCTS ARE SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY. MOREOVER, DAMAGE RESULTING DIRECTLY OR INDIRECTLY FROM IMPROPER INSTALLATION OR SETUP IS SPECIFICALLY EXCLUDED FROM COVERAGE UNDER THIS LIMITED WARRANTY EFFECTIVE WARRANTY DATEIMPORTANT WARRANTY REGISTRATION CONTACT A RUNCO AUTHORIZED SERVICE CENTER TO OBTAIN SERVICESafty metal fittings How to Attach Options to the Plasma MonitorWall* Safety metal fittings will differ according to the model Screw hole Screw or Hook etc Not suppliedFront View Part Names and FunctionRear View / Terminal Board Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement 1. Press and open the cover3.Replace the cover Using the wired remote control mode Operating RangeHandling the remote control Plasma Monitor Installation Signal Source with DVI outputTo Mini D-Sub 15 pin connector on the plasma monitor Connections with Equipment that have a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD PlayerPin Configuration and Signal of the RGB 3 Connector DVI Connector Pin Assignments and Signal Levels for 15 pin RGB AnalogCreating a video wall Cable ManagementInformation PFP Controller Installation & Overall Description Front Panel PFP Controller DescriptionRear Panel RUNCO PFP Controller Remote DescriptionConnection Examples Quick Set-up GuideMenu Description and Navigation Menu TreeMain Menu white Picture Quality AdjustmentsMenus are only available during “Installer Mode” Main MenuAbove black Set contrast until there is no blooming in this bar Below blackNote Luma Enhance will only appear in the menu after the installation mode has been enabled Side Bar Level Installation MenuInvert Runco PL-61cxSide Bar Level been reset, the IR code set will default to Output ShiftInput Shift IR Code SelectSystem Reset BlankingBlanking Basic Operations POWERVOLUME AUTO ADJUSTAfter the power is turned off with the off timer OFF TIMERTo set the off timer To cancel the off timerZOOM size screen WIDE OperationsWide Screen Operation manual When viewing videos or digital video discs “ PICTURE SIZE” setting Wide Screen Operation with Computer SignalsWhen “ PICTURE SIZE” is set to “ OFF” Supported resolutionNote The main menu disappears by pressing the EXIT button Menu Operations Advanced menu mode OSMOn Screen Menu ControlsMenu Tree 1 Only when AUTO PICTURE is OFF 2 RGB/PC only 3 Cannot be set in some modelsDAYLIGHT SAIVING TIME Note If “CAN NOT ADJUST” appears Picture Settings MenuAdjusting the picture Setting the picture mode according to the brightness of the room Restoring the factory default settings Setting the color temperatureAdjusting the color to the desired level Setting the color temperature GAMMA settings Making the Low Tone adjustments Adjusting the white balance Restoring the factory default settings COLOR TUNE settings Audio Settings MenuAdjusting the colors To continue making other adjustments Restoring the factory default settings Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture Adj Adjusting the Auto Picture Option1 Settings MenuSetting the on-screen menu When “ AUTO PICTURE” is “ OFF” OSM ORBITER settings Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal Setting a computer image to the correct RGB select screen3. To set the HD SELECT mode to “1035I” Setting high definition images to the suitable screen sizeSetting the Input Skip Restoring the factory default settings3. To turn the power management function on Option2 Settings MenuResetting to the default values Setting the power management for computer images CINEMA MODE POWER/STANDBY indicatorSetting the picture to suit the movie 3. To set the CINEMA MODE to “OFF”Perform Steps 1-2 of LONG LIFE, then ORBITER settings ORBITER Function settings INVERSE Settings To select “ ON” for the “ WORKING TIME” Setting the timePerform Steps 1-3 of INVERSE, then InformationSetting the gray level for the sides of the screen Setting the screen size for S1/S2 video input Setting the time SOFT FOCUS settings Restoring the factory default settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal S1/S2 settingsPerform Steps 1-2 of TIMER, then Option3 Settings MenuUsing the timer Restoring the factory default settings To reset the data Setting the power on modePerform Steps 1-2 of TIMER, then To reset the program CONTROL LOCK settings Enabling/disabling remote control wireless transmission PWR. ON MODE settings Restoring the factory default settings If the RGB/PC1 signal is present at the time the power switched on Loop Out settingID number setting LOOP OUT settings DIVIDER settings Video Wall setting4. Once the setting is completed Restoring the factory default settingsPerform Steps 1-2 of VIDEO WALL, then AUTO ID settings DISP. MODE settings IMAGE ADJUST settingsInformation P. ON DELAY settings PLE LINK settings Perform Steps 1-2 of VIDEO WALL, then ADVANCED OSM settings Advanced OSM Settings MenuSetting the menu mode REPEAT TIMER settingsSetting the language for the menus Language Settings MenuColor System Settings Menu Source Information MenuCommunication Parameters External ControlApplication ConnectionsTable of Signals Supported Supported resolutionComputer input signals supported by this system PFP Controller RS-232 Communications General InformationDESCRIPTION COMMANDPARAMETER min/max Value stored?DESCRIPTION COMMANDPARAMETER min/max Value stored?Remedy TroubleshootingSymptom Checks1 Overheat Protector after initial installation. The PFP Controller TroubleshootingPROBLEM SOLUTIONof definition in the bright on, and the power LED onThe image appears too bright, and there is a lossPlasma Monitor Specifications & Dimensions Front Panel Rear Panel Top Panel Side Panel PFPTM Controller Specifications & DimensionsRUMA-006830-SPL