PFP Controller Description, Front Panel | Runco PL-61CX specs

PFP™ Controller Description

Front Panel

1 2 3

ratio

< enter

<>

<

ratio

i n p u t

menu

4

5

6

7

8

9

10

1.IR RECEIVER

Receives the infrared signal from the remote control.

2. POWER BUTTON

Turns the unit ON or OFF. The Main Power switch on the rear of the unit must be on first for this button to be active.

3.POWER INDICATOR

When the PFP Controller is ON, this LED will illuminate GREEN. When the unit is OFF or in STANDBY, this LED will illuminate RED. A flashing red light indicates a fault. If this happens, unplug the unit for 2 minutes and re-try. A yellow LED indicates a communication problem; double check that the ComLink cable is connected properly.

4.LED DISPLAY

Indicates the model number, current source, resolution and aspect ratio.

5.UP BUTTON

When no menu is present on-screen, this button will toggle you through the different aspect ratios. When the menu is on-screen, the UP button will move the cursor up within a menu.

When an adjustment item has been selected (i.e. brightness), the UP button will increase the value of that function.

6.LEFT BUTTON

When no menu is present on-screen, the LEFT button will toggle you through the five different sources, in the order of:

RGB HD		Component HD		Component		S-Video		Composite

7.ENTER BUTTON

When an item is highlighted on the On-Screen Display, the ENTER button will select the item.

8.DOWN BUTTON

When no menu is present on-screen, this button will toggle you through the different aspect ratios. When the menu is on-screen, the DOWN button will move the cursor down within a menu.

When an adjustment item has been selected (i.e. brightness), the DOWN button will decrease the value of that function.

9.RIGHT BUTTON

When no menus are present on-screen, the RIGHT button will toggle you through the five different sources, in the order of:

Composite		S-Video		Component		Component HD		RGB HD

10.MENU BUTTON

The MENU button brings up the main adjustment menu. After making adjustments, the MENU button will bring you back to the sub-menu, then to the main menu. The menu will then either time-out after approximately 10 seconds, or pressing the MENU button will remove the menu immediately.

13

Image 23

Runco PL-61CX manual PFP Controller Description, Front Panel

Contents

PL-61cx Table of Contents External Control Options Features you’ll enjoy includeContents of the package Introduction Risk of Electric Shock Do not Open PrecautionsImportant Information Recommendations to avoid or minimize phosphor burn-in Plasma monitor cleaning procedureTo avoid damage and prolong operating life Three Year Limited Warranty RIGHTS, Limits and Exclusions TWO Year Limited Warranty RIGHTS, Limits and Exclusions How to Attach Options to the Plasma Monitor Part Names and Function Turns the plasma monitor’s power on and offReceives the signals from the remote control Sets the On-Screen Menu mode and displays the main menu Connect DVD’s, High Definition or Laser Discs, etc here Connect the included power cord hereRear View / Terminal Board Installation Remote Control Use of Installation Remote Control Battery Installation and Replacement 1/8 Stereo Mini cable must be purchased separeately Using the wired remote control modeOperating Range Video Plasma Monitor Installation Connections with Equipment that have a Digital Interface Connecting Your Document CameraConnecting Your VCR or Laser Disc Player Connecting Your DVD Player Pin No Signal Analog Pin Assignments and Signal Levels for 15 pin RGB Analog Cable Management Creating a video wall PFP Controller Installation & Overall Description Front Panel PFP Controller Description RGB Output Video Inputs Rear Panel PFP Controller Remote Description Connection Examples Quick Set-up Guide Main Menu Menu Tree Picture Quality Adjustments Page Page Side Bar Level Installation Menu Invert IR Code Select Output ShiftInput Shift Blanking System ResetBlanking Basic Operations To check the remaining time To set the off timerTo cancel the off timer After the power is turned off with the off timer Wide Operations When viewing videos or digital video discs Picture Size setting Wide Screen Operation with Computer SignalsWhen Picture Size is set to OFF Supported resolution Menu Operations Advanced menu mode Menu Tree Reset OPTION2 PWR. MGT Adjusting the picture Picture Settings Menu Reducing noise in the picture Setting the color temperatureAdjusting the color to the desired level LOW Tone settings Making the Low Tone adjustments Adjusting the white balance Gamma settings Audio settings menu Audio Settings MenuAdjusting the colors Color Tune settings Example Setting Audio INPUT1 to Video Image Adjust Settings MenuSetting the allocation of the audio connectors Adjusting the Position, Size, Fine Picture, Picture Adj Setting the on-screen menu Option1 Settings Menu OSM Orbiter settings Setting the BNC connectorsChecking the signal being transmitted to RGB1 terminal Setting a computer image to the correct RGB select screen RGB Select modes Setting high definition images to the suitable screen sizeSetting the Input Skip Input Skip settings Setting the power management for computer images Option2 Settings MenuResetting to the default values Reducing burn-in of the screen POWER/STANDBY indicatorSetting the picture to suit the movie PLE settings Inverse Settings Orbiter settings Orbiter Function settings Screen Wiper Setting the time To select on for the Working Time Gray Level settings Setting the screen size for S1/S2 video input Soft Focus settings Setting the gray level for the sides of the screen PLUG/PLAY settings Setting the picture size for RGB input signalsSetting the signal and black level for DVI signal S1/S2 settings Present Time Option3 Settings MenuUsing the timer Present Time settings Special characters in the Program Timer screen Setting the power on mode To reset the program To reset the data IR Remote settings Enabling/disabling remote control wireless transmission PWR. on Mode settings Control Lock settings ID number setting Loop Out setting Screens Video Wall setting Divider settings Video Wall Position settings Image Adjust settings Auto ID settings DISP. Mode settings PLE Link On Delay Power on delay P. on Delay settings PLE Link settings Repeat Timer settings Advanced OSM Settings MenuSetting the menu mode Repeat Timer Setting the video signal format Language Settings MenuColor System Settings Menu Setting the language for the menus Communication Parameters External ControlApplication Connections Computer input signals supported by this system Table of Signals SupportedSupported resolution General Information PFP Controller RS-232 Communications Parameter min/max Value stored? PFP Controller RS-232 Commands Store YES Symptom Checks Remedy TroubleshootingPage Plasma does not turn on After initial installation.Power LED on the front Yellow after the power button Definition in the bright On, and the power LED onImage appears too Bright, and there is a loss 169 Weight 140 lbs .5 kg1366 x Diagonal Pfptm Controller Specifications & Dimensions RUMA-006830-SPL