To protect refrigerator in movement | Samsung RS2666, RS2544, RS2622

2. INSTALLATION

1)To protect refrigerator in movement

Use padded hand truck as shown. If entrance width is less than 39〃, remove doors prior to installation and reattach doors according to procedure below.

2) Remove all protective tape and pad in refrigerators. Connect water lines and power cord. Adjust the clearance between the doors.

3) Set the temperature control to the temperature and wait for an hour.

The refrigerator should get slightly chilled and the motor runs smoothly.

4) Once the refrigerator temperature is sufficiently low You can store food in the refrigerator. After starting the refrigerator, it takes a few hours to reach the appropriate temperature.

● Removing Doors

● Attaching Doors

Open the freezer and refrigerator doors, and

Insert the lower hinge in the bracket lower

then take off the front leg cover assembly by

hinge. Attach the freezer door by inserting the

turning the three screws counter-clockwise.

hose in the lower side of the door into the hole in

Remove the screw from clamp disconnect, the

the lower hinge and pulling the hose down.

water tube by pressing the coupler, and pulling

the water tube away.

						Insert the upper hinge shaft into the hole. After
With the door closed, remove the upper hinge						leveling between the upper hinge hole and the
cover using a screwdriver, and then disconnect						hole of the cabinet. Reattach hinge screws and
the wires. Remove hinge screws and ground						screw in the clockwise direction. Connect the
screw counter-clockwise, and take off the upper						wires. Put the front part of the upper hinge cover
hinge. Take care removing the door to ensure that						on the front part of the upper hinge and reattach
it does not fall on you.						from the front part of the upper hinge cover first.
Remove the door from the lower hinge by
carefully lifting the door so as not to damage the
carefully lifting the door so as not to damage the
water tube. Remove the lower hinge from the
lower hinge bracket by lifting the lower hinge.
lower hinge bracket by lifting the lower hinge.

5

Image 5

Samsung RS2666 To protect refrigerator in movement, With the door closed, remove the upper hinge, It does not fall on you

Contents

Model RS2544 RS2622 RS2644 RS2666 RS2777 Important Safety Notice Contents Multi-Flow System Door AlarmXtra SpaceTM Xtra FreshTM To protect refrigerator in movement Cover using a screwdriver, and then disconnectWith the door closed, remove the upper hinge It does not fall on you Models NomenclatureCompany Name Product R Refrigerator Label Location Freezer Refrigerator Specifications Warranty information Shelves and Bins Interior Views and DimensionsFreezer Refrigerator Dimensions of Refrigerator Inches Refrigerant Route in Refrigeration cycle Refrigeration Cycle and Cool Air Circulation RouteFreezer Evaporator Dryer Capillary Tube Cool Air Circulation Freezer Refrigerator Refrigerator Disassembly Mechanical DisassemblyFreezer Disassembly PlasticWire Drawer in Freezer······························ Door Handle Control PanelBeverage StationTM Door Gasket Refrigerator Light Refrigerator Door Light SwitchTempered Glass Shelf Plastic Drawers in Refrigerator Upper Ductwork Water FilterEvaporator Cover in the Refrigerator Evaporator Fan Motor Refrigerator Thermistor Evaporator in RefrigeratorCoolSelect ZoneTM Thermistor CoolSelect ZoneTM Thermistor Plastic Wire Drawer in Freezer Freezer Door Light SwitchDoor Bin in Freezer Freezer Shelf Disconnect the ice maker wire connector Ice maker is located inside of the ice dispenser assemblyAuger Motor Case Unlock the locking tabs to separate the ice maker kit Evaporator Cover in Freezer Freezer Light Freezer Thermistor Evaporator in FreezerAmbient Thermistor Ice-MakerThermistor Water Solenoids Machine Compartment ＆ Electric BoxCondenser Fan Sub-condenser Operation Function Digital Panel Temperature Control Function Child Lock Function Quick Ice and Power Cool FunctionsPower FreezeQuick Ice function CoolSelect ZoneTM Function RS2666,RS2777 Fan Motor Delay Function of the Machine CompartmentIce & Water Dispenser Function Ice-Maker Function Water Filter Indicator FunctionFilter Indicator Initial Operation function Preparation of Ice-makerJudgement Remark ·MICOM Port Defrost Function Water Supply functionHeater on Heater OFF Defrost operation Self-Diagnostics Function Beeps will cease immediately when the doors are closedSelf-Diagnostics in the initial Power on Sound Function Error items of self-diagnostics ErrorFunction error Error items LED Display Details Remarks This mode, only the display LEDs for temperature will be on Restoration Function for Power OutageLoad Operation Check Function Set Point Shift Function Table of Set Point Shift Function Shift the freezer temperature sensor Operation Function Shift the Ice maker temperature sensor Shift the CoolSelect ZoneTM temperature sensor Circuit Descriptions Reset Circuit Source Power CircuitOscillator Circuit Terminal Door S/W Sensing Circuit Temperature Sensing CircuitMicom Change Key Scan and display operation DEF-sensor and Bimetal work in parallelKey Scan and Display Circuit Key Scan CoolSelect ZoneTM Panel Circuit Voltages between high-speed and low-speed Fan Motor Bldc Drive CircuitMotor drive circuit Option Circuit Eeprom CircuitLoad Drive Circuit D602 COMP. equivalence circuit of drive section If power is not on DiagnosticsStart Normal If the compressor and cooling fan motor don’t work normally AssemblyCheck after a lapse of 5 min Connection Perform forced defrosting for F Room at a time If defrost functionExchange and troubleshoot Corresponding sensor If there is a trouble with self-diagnosis If the temperature sensor of F and R room has troubleIf the ambient sensor has trouble Start Check if the iced solder of main PCB is Short If Ding-Dong sounds continuously Start If alarm soundIf Beep sounds continuously Start Remove causes after Display’ Without sound of buzzer operation StartMain PCB is normal buzzer normal ZoneTM panel If the panel PCB is not working normally Connections of door S/W If fan doesn’t work ReferenceDoor open DC Door close If the lamp of CoolSelect ZoneTM is not lit Start If CoolSelect ZoneTM isn’t operated normally RS2555, RS2577If the Panel PCB key isn’t selected Panel PCB has trouble for itself Is the inside lamp filament cut? If the lamps of freezer / refrigerator does not light Check the operation of SSR71 and Q701 If Crushed Ice/Cubed Ice doesn’t work properly Safety Instructions on Service DC 0V Stop Condition Appendix ⅠReference for circuit diagnosticsResistance value ∼DC 12V load working condition Value Contents For safety, you must turn the power off LoadRef Check a load Ref. Def heater Lamp Lamp on the REF Ref Check Door S/W 834 878791 749 Part Name Specifcation ’TY Ref Service part lists of each circuit boardPage Page Refrigerator Division 2003 Code DA82-00001D Electronics