Manuals / Sanyo / Household Appliance / Air Conditioner

Sanyo 85464359982001 installation instructions Name Of Parts, Care And Cleaning

Models: 85464359982001

1 96

Download 96 pages 22.69 Kb

Page 89

Manual background

07-007 W-2WAY_II_NA 1/23/07 6:09 PM Page 89

9-3. Concealed Duct (High-Static Pressure) Type (U, D Type)

■NAME OF PARTS

CONCEALED DUCT	CONCEALED DUCT
U type (standard static pressure)	D type (high static pressure)

Flexible duct (optional)

Water drain

Air intake

sideduct flange (rear)

Water drain

Air outlet grille (optional)

Canvas duct (optional)

Air intake grille (air intake) (optional)

Electrical box

Air outlet side duct flange

U

■CARE AND CLEANING

			1.	For safety, be sure to turn the air conditioner off and also to disconnect the power before
	WARNING		1.
	WARNING			cleaning.
			2.	Do not pour water on the indoor unit to clean it. This will damage the internal compo-
				nents and cause an electric shock hazard.

Air intake and outlet side Clean the air intake and outlet side of the indoor unit with a vacuum cleaner brush, or wipe them (Indoor unit) with a clean, soft cloth.

If these parts are stained, use a clean cloth moistened with a mild liquid detergent. When clean- ing the air outlet side, be careful not to force the vanes out of place.

	1.	Never use solvents or harsh chemicals when cleaning the indoor unit. Do not wipe plastic
CAUTION		parts using very hot water.
	2.	Some metal edges and the fins are sharp and may cause injury if handled improperly; be
	2.
		especially careful when you clean these parts.

3.The internal coil and other components of the outdoor unit must be cleaned every year. Consult your dealer or service center.

	Type	Period	*Concealed duct type (U, D):
	Type	Period	An air filter is not provided with this air conditioner at the time of shipment. To get clean air

	U, D*	(Depends on filter
	U, D*	(Depends on filter	and to extend the service life of the air conditioner, an air filter must be installed in the air
		specifications)
			intake. For installation and cleaning the air filter, consult your dealer or service center.

NOTE

The frequency with which the filter should be cleaned depends on the environment in which the unit is used.

<How to clean the filter>

1.Remove the air filter from the air intake grille.

2.Use a vacuum cleaner to remove light dust. If there is sticky dust on the filter, wash the filter in lukewarm, soapy water, rinse it in clean water, and dry it.

D

89

Image 89

Sanyo 85464359982001 installation instructions Name Of Parts, Care And Cleaning

Contents

R410A Models Indoor Units X A U D T KOutdoor Units Optional ControllersELECTRICIAN SHOULD ATTEMPT TO WIRE THIS SYSTEM SPECIAL PRECAUTIONS…In a Room …In Moist or Uneven LocationsCheck of Density Limit Manifold gauge Vacuum pump 1. Care regarding tubing3. Different tools required Single-outletvalve 1. Compressor specifications are different2. Existing tubing cannot be used especially R22 R410A3.HOW TO INSTALL THE INDOOR UNIT CONTENTS4-WayAir Discharge Semi-ConcealedType X Type 1-WayAir Discharge Semi-ConcealedType A Type6. HOW TO PROCESS TUBING . . . . . . . . . . . . 1-1.Tools Required for Installation not supplied 1. GENERAL1-2.Accessories Supplied Refer to “5. ELECTRICAL WIRING” for detailsTable 1-3 1-WayAir Discharge Semi-Concealed Table 1-2 4-WayAir Discharge Semi-ConcealedTable 1-4Concealed Duct Part NameTable 1-6 Ceiling-Mounted Table 1-5Concealed Duct High-StaticPressureTable 1-7 Wall-Mounted Part Namelength Allowable tubing1, 2... L1+ 1+ 2 ...Size of tubing LO between outdoor units 1-7.Straight Equivalent Length of Joints unit is installed 1-10.Check of Limit Density Model name 1-12.Optional Distribution Joint KitsCooling capacity after distribution Remarks460,700 BTU/h 135.0 kW Table 1-21Size of connection point on each part Shown are inside diameters of tubing232,000 BTU/h 68.0 kW Additional refrigerant charging Minimum room volume for indoor unit: ft.3 the room in which the indoor unit is installedMain tubing Distribution joint tubingCeiling-MountedType 2. SELECTING THE INSTALLATION SITE1-WayAir Discharge Semi-ConcealedType Wall-MountedTypeTop view 2-2.Outdoor Unit AVOID2-3.Shield for Horizontal Exhaust Discharge 2-unitinstallation 2-6.Dimensions of Wind Ducting2-7.Dimensions of Snow Ducting 3-2.Suspending the Indoor Unit 3.HOW TO INSTALL THE INDOOR UNITTable Fig.Tighten the hose clamps so 3-4.Installing the Drain Pipingtheir locking nuts face upward Fig.3-5.Checking the Drainage start when you short the pinBe careful since the fan will on the indoor control boardRemoving the corner cover 3-6.How to Install the Ceiling PanelFig. Fig.Fig. 3-6-2.Installing the Ceiling PanelFig. Fig.3-6-4.How to Attach the Corner & Air-IntakeGrille 3-6-3.Wiring the Ceiling PanelAttaching the corner cover and air-intakegrille Fig.3-6-7.Adjusting the Auto Flap 3-6-5.Checking After Installation3-7.Special Remarks DC Fan Tap Change Procedure Fig.Fig. Fig.Fig. 3-9.Placing the Unit Inside the CeilingFig. Fig.Fig. 3-10.Installing the Drain PipingFig. Fig.3-11.Checking the Drainage Do not use natural drainageFig. Fig.2 Wiring 3-12.Electrical Power Wiring 1 Wiring connections3-13.How to Install the Ceiling Panel 3-13-1.Before Installing the Ceiling PanelRemoving the intake grille Fig. 3-13-2.Installing the ceiling panelRemoving the side panel Fig. 3-49aFig. Fig.Fig. Must be no gap Indoor unitA. Installing the side panel 3-13-3.Wiring the ceiling panelB. Installing the intake grille 3-13-5.Other A. Check after installationTable Concealed Duct Type U TypeFig. TableFig. 3-15.Suspending the Indoor UnitFig. Fig.indoor unit 3-16.Installing the Drain PipingThe maximum permissible bend is 3-17.Checking the DrainageHow to read the diagram Be careful since the fan will start when youshort the pin on the indoor control board 3-18.Increasing the Fan SpeedConcealed Duct High-StaticPressure Type D Type TableFig. Fig.3-20.Suspending the Indoor Unit enough to suport the weight of the unitIt is important that you use extreme care in supporting the indoor unit inside theHow to Read the Diagram 3-21.Installing the Drain Piping3-22.Caution for Ducting Work 3-23.Indoor Fan PerformanceService 3-24.Required Minimum Space for Installation and2 Refrigerant tubing • drain hose position Ceiling-MountedType T Type4 Wall and ceiling side opening position weight of the unit. BeforeFig. 3-25.Suspending the Indoor Unit It is important that you useFig. Fig. Fig.Fig. Fig.3-26.Duct for Fresh Air Fig. 3-28.Installing the Drain Piping3-27.Shaping the Tubing Fig.When removing the fastening THow to carry out power supply wiringand regulations before wiring bracket from the cover of the3-30.Selecting and Making a Hole 3-29.Removing the Rear Panel from the UnitWall-MountedType K Type Fig.Removing the grille b If the Wall is Brick, Concrete or SimilarAttaching the grille 3-33.Preparing the Tubing3-34.Shaping the Tubing Right-reartubing 3-35.Installing the Drain HoseLeft or left-reartubing unit are completedKHX2452 KHX0752 / 0952 / 1252 /Setting at time of factory shipment Setting at time of4-2.Installing the Outdoor Unit 4. HOW TO INSTALL THE OUTDOOR UNIT4-1.Transporting Fig.Fig. 4-3.Routing the TubingFig. Refrigerant tubing Existing tubing can be used 4-4.Prepare the TubingTubing size in. mm Material OTightening torque for each cap Refrigerant tube port0905 Type 1405 TypeAWG #8 5. ELECTRICAL WIRING64 ft 60 AK Type 5-3.Wiring System DiagramIndoor unit Outdoor unitOutdoor unit Indoor unitShielded wire GroundGround How to connect wiring to the terminal6-1.Connecting the Refrigerant Tubing 6. HOW TO PROCESS TUBINGFlaring Procedure with a Flare Tool Use of the Flaring Method120 – 160 lbs · inch ø1/4 ø6.35 mm1/32 140 – 180 kgf · cmThree tubes arranged together Two tubes arranged together6-4.Taping the Tubes 6-5.Finishing the InstallationFig. Fig.Vacuum pump Manifold gaugeEvacuation when 30 gal/h vacuum pump is usedRequired time for evacuation 45 min. or moreUse a cylinder designed for use R410Awith R410A respectively Charging additional refrigerant8-1.Preparing for Test Run 8. TEST RUNFig. Fig.Items to Check Before the Test Run 8-2.Test Run ProcedureFig. 8-3.Main Outdoor Unit PCB SettingS003 S002 S004 S005 S006 S007 CN100 CN101 CN003 07-007 W-2WAY II NA1/23/07 6 09 PM PageIndoor unit setting S005 Fig. 3 units, and set the unit No. DIP switch S007 to1-10 unit No.1-13 Basic wiring diagram: Example2-22-9 Fig.1. On the No Automatic Address Setting from Outdoor UnitOn the No. On the No.Automatic Address Setting from Outdoor Unit Automatic Address Setting in Heating ModeCase 3A CaseAutomatic Address Setting from Outdoor Unit Automatic Address Setting in Cooling ModeCase 3B CaseRemote controller display Display during automatic address settingOn outdoor main unit PCB LED 1 is D72. LED 2 is D75Checking the indoor unit addresses 8-5.Remote Controller Test Run Settings8-6.Caution for Pump Down M = 2: P alarm Alarm display3: H alarm 4: E alarm 5: F alarm 6: L alarm N = Alarm NoActivation of AlarmContinued Alarm messages displayed on system controller 9. APPENDIX CARE AND CLEANING9-1. 4-WayAir Discharge Semi-ConcealedType X Type NAME OF PARTSTips for Energy Saving TROUBLESHOOTINGNAME OF PARTS 9-2. 1-WayAir Discharge Semi-ConcealedType A TypeCARE AND CLEANING Outdoor unit TROUBLESHOOTINGTips for Energy Saving NAME OF PARTS CARE AND CLEANINGShould the power fail while the unit is running TROUBLESHOOTINGTips for Energy Saving Avoid DoNAME OF PARTS 9-4. Ceiling-MountedType T TypeCARE AND CLEANING or soot TROUBLESHOOTINGTips for Energy Saving CARE AND CLEANING 9-5. Wall-MountedType K Type NAME OF PARTSor soot TROUBLESHOOTING