Sanyo 85464359982001 Case, Auto Address Setting Basic wiring diagram Example

(S004) 0

No. of indoor units (10 units setting)

07-007 W-2WAY_II_NA 1/23/07 6:09 PM Page 74

8-4. Auto Address Setting

Basic wiring diagram: Example (1)

• If link wiring is not used

(The inter-unit control wires are not connected to multiple refrigerant systems.) Indoor unit addresses can be set without operating the compressors.

No. 1 (main outdoor unit) settings

System address (system 1 setting)

(S002) (S003)
ON		ON		(S005)
1	2	OFF		ON		ON
No. of				1 2	3	OFF
	(S006)			Unit number	(S007)
outdoor			ON
units (3 units	ON			setting	ON	ON
setting)	1	2 3	OFF	(Unit No. 1)	1 2	3 OFF

No. 2 (sub unit) settings

Unit		(S007)
number	ON				ON
setting			2		OFF
(Unit No. 2)		1		3

No. 3 (sub unit) settings

Unit		(S007)
number	ON			ON
setting				OFF
	1 2
(Unit No. 3)			3

Unit

Outdoor Unit No. 1

(Main)

Leave the socket that
is used to short-circuit	Unit		Unit
the terminal plug.
(CN003)	No. 2		No. 3
	(Sub)		(Sub)
Outdoor main/sub		Outdoor main/sub
control wiring		control wiring

Inter-unit control wiring

Indoor Unit	1-1	1-2	1-3	1-10
				Remote controller
Remote controller				cross-over wiring

Case 1

Fig. 8-5

(1) Automatic Address Setting from the Outdoor Unit

1. To set the number of outdoor units, on the outdoor main unit control PCB set the No. of outdoor units DIP switch (S006) to

	ON				ON	(3 units), and set the unit No. DIP switch (S007) to	ON							(unit No. 1 – main outdoor unit).
							1			2		3
		1	2	3	OFF
								ON
2. On the No. 2 (sub) unit control PCB, set the unit No. switch (S007) to															(unit No. 2).
									1		2		3
On the No. 3 (sub) unit control PCB, set the unit No. switch (S007) to								ON							(unit No. 3).
									1		2		3

3.	On the outdoor main unit control PCB, check that the system address rotary switch (S002) is set to “1” and that the DIP switch
	(S003) is set to ON			ON
				“0.” (These are the settings at the time of factory shipment.)
		1	2	OFF
4.	To set the number of indoor units that are connected to the outdoor unit to 10, on the outdoor main unit control PCB set the No. of
						ON “1,” and set the rotary switch (S004) to “0.”
	indoor units DIP switch (S005) to				ON

1 2 3 OFF

5.Turn ON the power to the indoor and outdoor units.

6.On the outdoor main unit control PCB, short-circuit the automatic address pin (CN100) for 1 second or longer, then release it.

↓

(Communication for automatic address setting begins.)

*To cancel, again short-circuit the automatic address pin (CN100) for 1 second or longer, then release it.

↓The LED that indicates that automatic address setting is in progress turns OFF and the process is stopped. Be sure to perform automatic address setting again.

(Automatic address setting is completed when LEDs 1 and 2 on the outdoor main unit control PCB turn OFF.)

↓

7. Operation from the remote controllers is now possible.

*To perform automatic address setting from the remote controller, perform steps 1 to 5, then use the remote controller and com- plete automatic address setting.

●Refer to “Automatic Address Setting from the Remote Controller.”

74