SSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSSS

F66 – Daylight Saving Time (DST)

K,N,S,W

Schedule when DST starts and ends (Local time only)

Mode

 

 

 

F69 – Time Mode

K,N,S,W

Set the time scale (TAI, GPS, UTC, Standard, Local) output

 

 

 

by the IEEE 1588 card and displayed on the front panel of

 

 

 

the XLi. (TAI is the recommended setting).

F71 – Oscillator Statistics

K,N,S,W

Display the XLi oscillator’s phase, offset, drift, and DAC

 

 

 

values

F72 – Fault Status

K,N,S,W

View clock and power supply fault status

F73 – Alarm Control / Status

K,N,S,W

View the status of all the alarm indicators. Enable/disable

 

 

 

alarms for each indicator. Set alarm thresholds. Enable or

 

 

 

disable LED blink

F74 – Clock Source Control

K,N,S,W

Select the pattern of switching between reference sources

F90 – Code Output Configuration

K,N,S,W

Configure settings for CODE – time code output

F100

– Network Port Configuration &

K,N,S,W

Configure the standard network port settings

XLi Firmware

 

 

F100

EA – Ethernet Address

K,N,S,W

Display the Ethernet (MAC) address

F100

IP – IP Address

K,N,S,W

Configure the IP address

F100 SM – Subnet Mask

K,N,S,W

Configure the subnet mask

F100 G – Gateway

K,N,S,W

Configure the default gateway

F100

IC – Network Port Settings

K,N,S,W

Display all the standard network port’s settings

F100 L/LOCK/UNLOCK – Remote

K,N,S

Lock remote access to the XLi’s standard network port

Lockout

 

 

F100

L – Remote Lockout

K,N*,S

Display the status of F100 LOCK

 

 

 

*Locked through the network port, serial port, and keypad.

 

 

 

Can be unlocked only through the keypad or serial port.

F100

ST – Self Test Status

K,N,S

Display the XLi’s self test results for Flash CRC, RAM,

 

 

 

Serial Port, and NVRAM

F100 BH – Burn Host

N,S

Upgrading system firmware: select the FTP host, path, and

 

 

 

filename of the system firmware

F100

BUB – Burn BootLoader

N,S

Upgrading system firmware: ‘burn’ the bootloader file (*.bt)

 

 

 

selected using F100 BH to flash memory

F100 BU – Burn

N,S

Upgrading system firmware: ‘burn’ the system firmware file

 

 

 

(*.bin) selected using F100 BH to flash memory

F100

BF – Burn File System

N,S

Upgrading system firmware: ‘burn’ the file system file (*.fs)

 

 

 

selected using F100 BH to flash memory

F100 BUFP – Burn FPGA Firmware

N,S

F100 CONFIG – Configure NTP &

N,S,W*a

SNMP

 

F100 J – Factory Mode Jumper

N,S

Upgrading system firmware: burn the FPGA program file (*.bin) selected using F100 BH to the flash memory

Transfer the SNMP configuration file between the XLi and an FTP server for editing

View the status of the factory mode jumper, which is used by factory technicians. Not of interest to most end users.

36

XLi IEEE 1588 Clock

997-01510-03, Rev. C, 12/12/2006

Page 44
Image 44
Symmetricom XLi IEEE 1588 manual Snmp