Tandberg Data Tandberg LTO2 2.3 AC Power Cable Connection

- 10 -

When the SCSI connections end with this device (i.e., when connection to a separate device is

not made from the left-side connector), be certain to connect the terminator supplied with the

main unit. Failure to connect the terminator will result in improper operation of all connected

SCSI devices.

When connections are made to other SCSI devices with the Autoloader connected in an

intermediate position, connection to the next SCSI device is made from the left-side connector.

Be certain to attach the terminator to the SCSI device positioned at the farthest end of the chain

of devices that are connected by SCSI cable.

Please refer to the manuals supplied with the server/workstation and SCSI devices for

information about the method of connection to server/workstations and other SCSI devices.

Note that the SCSI cable is sold separately. Please purchase a SCSI cable that suits the connectors

of the Autoloader, the equipment to be connected, as well as the SCSI interface specifications.

Important

Once cable connections are completed, check that there are no kinks in the

connections. SCSI cable connectors are equipped with screws for securing the

connection. Please check that the connectors have been securely fastened with

the screws.

2.3 AC Power Cable Connection

When the connection to the signal cable or terminating connector is completed, check that the

power switch is OFF (switched to the " { " side).

After checking it, plug the AC power cord supplied with the main unit into the AC power

connector of this device. Ensure that the plug is inserted completely.

Figure 2-4 AC Power Cable Connection

Connect to the external AC power outlet

AC power cable

Contents

Main Trademarks CAUTIONS: Safety Precautions- Be sure to read this section before using this product. Safety Descriptions WARNING CAUTION Symbols and Their Meanings Used in This Manual and Warning Labels Safety Cautions General Cautions Cautions for power source or power cable into the outlet other than the one specified. Cautions for installing, transporting, storing, and connecting Do not cover the air inlet Cautions of maintenance Cautions during operation WARNING Label Revision History Contents Safety Precautions- Be sure to read this section before using this product. ............i Page Introduction Organization of this manual Symbols used in this manual Chapter1 Tandberg LTO2 Autoloader 1.1 Overview of the Tandberg LTO2 Autoloader 1.2 Names and Functions of the Parts 1.2.1 Front Panel of the Tandberg LTO2 Autoloader Page 1.2.2 Rear Panel of the Tandberg LTO2 Autoloader 1.2.3 Liquid Crystal Display 1.3 Handling Precautions 1.3.1 Main Unit 1.3.2 Cartridges 1.4 Transfer or Disposal of the Device 1.5 Contents of the Carton Chapter2 Setup 2.1 Preparation Before Use Removal of the Transporter Locking Screw and Instruction TAG 2.2 SCSI Cable Connections 2.3 AC Power Cable Connection 2.4 Attaching and removing the Filter Element 2.5 Switching ON the Power Switch and the Power-On Sequence 2.6 SCSI ID Setting 2.7 Start and Shutdown of the System Chapter 3 Operation 3.1 Removal of the Magazine 3.2 Loading the Magazine 3.3 Loading the Cartridge 3.3.1 Loading to Magazine 3.3.2 Loading to the Fixed Slots Operation Examples Page 3.4 Removal and Insertion of the Cartridges 3.4.1 Removal from and Insertion to the Magazine 3.4.2 Removal from and Insertion to the Fixed Slots Operation 5 3.5 Operation of the Panel Keys 3.5.1 Organization of the Front Panel Switches 3.5.2 Functions of the Switches 3.5.3 Slot Logical Numbers 3.5.4 Panel Operation Procedure Operation Examples 3.5.5 Menu Tree 1 Main Menu 2 Menu Commands 4) LOAD 5) SCSI ID 6) RETRY MODE 7) MAINTENANC 3.6 Setting the SCSI ID 3.6.1 Checking the SCSI ID 3.6.2 Changing the SCSI ID Operation Example 1 Operation Example 2 Page 3.7 Using the Emergency Release Key Chapter 4 Cartridges 4.1 Cartridges 4.1.1 Data Cartridge 4.1.2 Cleaning Cartridge 4.2 Write-Protect Switch 4.3 Bar Code Label Using Bar Code Labels Precautions 4.4 Handling Precautions 4.4.1 Usage Precautions 4.4.2 General Precautions 4.4.3 Standards for Prohibition of Use 4.4.4 Service Life 4.4.5 Storage of Data Cartridges Chapter 5 Daily Maintenance 5.1 Cleaning 5.1.1 Cleaning of the Drive Head 5.1.1.1 Manually Cleaning of the Drive Head 5.1.2 Cleaning the Roller inside of the transporter 5.1.2.1 Checking the CLNROL- function 5.1.2.2 Setting the CLNROL- function Disable 5.1.2.3 RtyCnt value in the CLNROL-function 5.1.2.4 Changing the RtyCnt value Page 5.1.2.5 Cleaning of the Roller 5.1.2.5.1 Execution timing of the cleaning 5.1.2.5.2 Tools and Parts 5.1.2.5.3 Setting Maintenance mode 5.1.2.5.4 Setting Cleaning mode 5.1.2.5.5 Cleaning the Roller Page Page Page Page 5.1.3 Cleaning of the Main Unit 5.1.3.1 Cleaning of the exterior FFC cable 5.1.3.2 Cleaning of the fixed slots 5.1.3.3 Cleaning of the interior 5.1.4 Cleaning of the magazine 5.1.5 Cleaning of the cartridge r shutte 5.2 Movement and Shipping of the Autoloader Chapter 6 Troubleshooting Page Page - 57 - Error code Cause Recovery Procedure - 58 - Error code Cause Recovery Procedure Page 6.1 Other Matters to Check 6.2 When Requesting Maintenance Appendix A Specifications Autoloader Main Unit LTO2 Data Cartridge (TD P/N: 432744) LTO1 Data Cartridge (TD P/N: 432630-1) Universal cleaning cartridge (TD P/N: 432631) Appendix B Optional Items and Supplies Optional Items Supplies Appendix C Error Code CMer Error CMer Error Code 2 CMer Error Code 3 Err. Messages Page Tandberg LTO2 Autoloader Installation and Users Manual