×××× | Tandberg Data Tandberg LTO2 specification

Err.

The displayed error codes are 4 digits and configured as described below. Example of error code display : Err. ××××

Table-D5 sorts the Err error codes and their contents.

	Table-D5 Err Error Code Table
××××	Description
0101	The Autoloader detected timeout error on communication with the drive.

0110	The Autoloader detected parity error on communication with the drive.

0111	The Autoloader detected framing error on communication with the drive.

0112	The Autoloader detected overrun error on communication with the drive.

0140	The Autoloader detected an error on the Load/Unload command.

0170	The Autoloader detected an error on the communication with the drive.

0180	The Autoloader detected an error on the communication with the drive.(NAK retry over)

0181	The Autoloader detected an error on the communication with the drive.(SNAK retry over)

0102～010F,	The Autoloader detected cartridge position or timeout error before issuing
0113～013F	Load/Unload/Unthread command.

0190	The Autoloader detected timeout error before issuing Unload command.

0191	The Autoloader detected timeout error before finishing Unload command.

0192	The Autoloader detected state error on communication with the drive.

4005～4007	The Autoloader detected an error during Eject from slot.

4008～400A	The Autoloader detected an error during Load to slot.

4011	Operating mistake.

4051～4053	The Autoloader detected an error during self- test(maintenace mode).

- 66 -

Image 82

Tandberg Data Tandberg LTO2 manual ××××

Contents

Tandberg LTO2 Autoloader FCC Class B Notice Trademarks Safety Descriptions Description example in this manual Prohibited action Mandatory action Safety Cautions General Cautions Do not apply starburst wiring Do not cover the air inlet Do not lift the device alone Do not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Troubleshooting Chapter Daily MaintenanceChapter Cartridges Introduction Organization of this manual Symbols used in this manual Symbols used in this manualTip Tandberg LTO2 Autoloader Overview of the Tandberg LTO2 Autoloader Names and Functions of the Parts Front Panel of the Tandberg LTO2 Autoloader ･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display Liquid Crystal Display LCD Main Unit Handling PrecautionsTransfer or Disposal of the Device Cartridges Contents of the Carton Preparation Before Use SetupTransporter Locking Screw Instruction TAG Scsi Cable Connections Storing the Transporter Locking Screw for later use AC Power Cable Connection AC Power Cable Connection Attaching and removing the Filter Element Attaching and removing a Filter Element Switching on the Power Switch and the Power-On Sequence Scsi ID Setting Start and Shutdown of the System Operation Removal of the Magazine Loading the Magazine Loading the Magazine Loading the Cartridge Loading to Magazine Loading to the Fixed Slots For using the Tandberg LTO2 Autoloader w/BCRs optionalOperation Examples For using the Tandberg LTO2 Autoloader w/BCR Removal and Insertion of the Cartridges Removal from and Insertion to the Magazine Removal from and Insertion to the Fixed Slots Display Eject Slot? Operation of the Panel Keys Organization of the Front Panel SwitchesFunctions of the Switches Slot Logical Numbers Panel Operation Procedure Display Frm Slt 1? Menu Commands Menu Tree 1 Main Menu Retry Mode Setting the Scsi ID Checking the Scsi ID Changing the Scsi ID Operation Example Tip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release Key Cartridges Cartridges Cleaning Cartridge Data Cartridge Write-Protect Switch Setting the Write-protect Switch Using Bar Code Labels Precautions Bar Code Label Usage Precautions General Precautions Standards for Prohibition of Use Service LifeStorage of Data Cartridges Cleaning Daily MaintenanceCleaning of the Drive Head Manually Cleaning of the Drive Head Default CLNROL-function setting Enable Cleaning the Roller inside of the transporterChecking the CLNROL- function Setting the CLNROL- function Disable RtyCnt value in the CLNROL-function Changing the RtyCnt valueOperation Example Tip Cleaning of the Roller Execution timing of the cleaning Tools and Parts Setting Maintenance mode Setting Cleaning mode Cleaning the Roller Shows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the fixed slots Cleaning of the Main UnitCleaning of the exterior Cleaning of the interior Cleaning of the magazine Cleaning of the cartridge Movement and Shipping of the Autoloader Troubleshooting Phenomenon Recovery Procedure Power Supply Phenomenon Recovery Procedure Cartridge Operation Connections Cleaning Phenomenon Recovery Procedure Autoloader PerformanceOthers Recovery Procedure P move system initialization Exceeding the recommended operation When Requesting Maintenance Other Matters to Check Appendix a Specifications Autoloader Main Unit Universal cleaning cartridge TD P/N LTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Optional Items Appendix B Optional Items and SuppliesSupplies Appendix C Error Code CMer Error Code Err ×××× Messages Messages Related to the Drive Interface Panel Operation and Other Messages Message Description Tandberg LTO2 Autoloader Installation and User’s Manual Tandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway