Safety Descriptions | Tandberg Data Tandberg LTO2 specs

Keep this operation manual on hand so that you can refer to it when needed. Be sure to read “Safety Precautions” before using this product.

Safety Precautions- Be sure to read this section before using this product. –

Safety Descriptions

This manual describes dangers that may be caused by ignoring the cautions and the ways to avoid those dangers. Warning labels are attached on the components that may cause danger.

“Warning” and “caution” terms are used for warning labels to describe the degree of the danger.

WARNING

CAUTION

This indicates a hazard that could lead to death or serious injury in the event of improper handling.

This indicates a hazard that could lead to burns, injury, or property damage in the event of improper handling.

The following three types of symbols are used for warnings and cautions. The meaning of each symbol is described below.

				This symbol indicates that danger could be	(Ex)
			Attention	caused if instructions are ignored. The	(Ex)
			Attention	figure in the symbol indicates details of the	(CAUTION:
				figure in the symbol indicates details of the
				danger.
				danger.	Electric shock)
			Prohibited	This symbol indicates prohibited action. The	(Ex)
			Prohibited	figure in the symbol or near the symbol
			action	figure in the symbol or near the symbol
			action	indicates details of the prohibited action.	(Do not
				indicates details of the prohibited action.	(Do not
					disassemble.)
			Mandatory	This symbol indicates mandatory action.	(Ex)
			Mandatory	The figure in the symbol indicates details of
			action	the mandatory action. The mandatory action
				is required to avoid danger.	(Unplug)
					(Unplug)

(Description example in this manual)

Term indicating the degree of danger

Details of caution to avoid danger

CAUTION

Only plug into specified electric outlet.

Plug the power supply cable into an electric outlet on the wall with specified voltage and power supply. Fire or electric leak may be caused if power supply other than the one specified is used.

Symbol prompting the caution

- i -

Image 3

Tandberg Data Tandberg LTO2 Safety Descriptions, Description example in this manual

Contents

Tandberg LTO2 Autoloader Trademarks FCC Class B Notice Description example in this manual Safety Descriptions Mandatory action Prohibited action General Cautions Safety Cautions Do not apply starburst wiring Do not lift the device alone Do not cover the air inlet Do not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Daily Maintenance Chapter TroubleshootingChapter Cartridges Introduction Organization of this manual Symbols used in this manual Symbols used in this manualTip Overview of the Tandberg LTO2 Autoloader Tandberg LTO2 Autoloader Front Panel of the Tandberg LTO2 Autoloader Names and Functions of the Parts ･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display LCD Liquid Crystal Display Cartridges Handling PrecautionsTransfer or Disposal of the Device Main Unit Contents of the Carton Setup Preparation Before UseTransporter Locking Screw Instruction TAG Storing the Transporter Locking Screw for later use Scsi Cable Connections AC Power Cable Connection AC Power Cable Connection Attaching and removing a Filter Element Attaching and removing the Filter Element Scsi ID Setting Switching on the Power Switch and the Power-On Sequence Start and Shutdown of the System Removal of the Magazine Operation Loading the Magazine Loading the Magazine Loading to Magazine Loading the Cartridge For using the Tandberg LTO2 Autoloader w/BCRs optional Loading to the Fixed SlotsOperation Examples For using the Tandberg LTO2 Autoloader w/BCR Removal from and Insertion to the Magazine Removal and Insertion of the Cartridges Display Eject Slot? Removal from and Insertion to the Fixed Slots Slot Logical Numbers Organization of the Front Panel SwitchesFunctions of the Switches Operation of the Panel Keys Panel Operation Procedure Display Frm Slt 1? Menu Tree 1 Main Menu Menu Commands Retry Mode Checking the Scsi ID Setting the Scsi ID Operation Example Changing the Scsi ID Tip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release Key Cartridges Cartridges Data Cartridge Cleaning Cartridge Setting the Write-protect Switch Write-Protect Switch Bar Code Label Using Bar Code Labels Precautions General Precautions Usage Precautions Service Life Standards for Prohibition of UseStorage of Data Cartridges Daily Maintenance CleaningCleaning of the Drive Head Manually Cleaning of the Drive Head Cleaning the Roller inside of the transporter Default CLNROL-function setting EnableChecking the CLNROL- function Setting the CLNROL- function Disable Changing the RtyCnt value RtyCnt value in the CLNROL-functionOperation Example Tip Execution timing of the cleaning Cleaning of the Roller Tools and Parts Setting Maintenance mode Cleaning the Roller Setting Cleaning mode Shows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the interior Cleaning of the Main UnitCleaning of the exterior Cleaning of the fixed slots Cleaning of the cartridge Cleaning of the magazine Movement and Shipping of the Autoloader Phenomenon Recovery Procedure Power Supply Troubleshooting Connections Phenomenon Recovery Procedure Cartridge Operation Phenomenon Recovery Procedure Autoloader Performance CleaningOthers Recovery Procedure P move system initialization Exceeding the recommended operation Other Matters to Check When Requesting Maintenance Autoloader Main Unit Appendix a Specifications LTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Universal cleaning cartridge TD P/N Appendix B Optional Items and Supplies Optional ItemsSupplies CMer Error Code Appendix C Error Code Err ×××× Messages Related to the Drive Interface Messages Message Description Panel Operation and Other Messages Tandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway Tandberg LTO2 Autoloader Installation and User’s Manual