Do not cover the air inlet | Tandberg Data Tandberg LTO2 specification

Cautions for installing, transporting, storing, and connecting

CAUTION

Do not lift the device alone.

This device weights 18 kg. Lifting it alone may injure your back. Be sure to transport or move the device with two persons.

Do not install in location other than the one specified.

Do not install this device in the location listed below or other than the location specified in this manual as a fire may occur.

･Dusty place

･Humid place such as near a hot water supply ･Install where exposed to direct sunlight

･Unstable place

Do not cover the air inlet

Do not cover the fan on the back panel and air inlet on the front panel of the device as internal temperatures will rise, resulting in a fire or an electric shock as well as operation error.

Do not connect/disconnect the interface cable with the plug still inserted in the outlet.

Remove the power cable from the outlet before connecting/disconnecting the interface cable. Touching cables or connectors while the power cable is connected may lead to an electric shock or a fire due to a short-circuit, even if the power is OFF.

Do not use an interface cable other than the one specified.

Use an interface cable specified by TD and connect it after checking the device or connector. Using an interface cable other than the one specified or connecting the cable to the wrong connection point may lead to a fire due to a short-circuit.

Follow the instructions described below for handling and connecting the interface cable.

･Do not step on the cable

･Do not place items on the cable

･Do not use the device with the cable connected loosely ･Do not use a damaged cable

･Do not use a damaged cable connector ･Be sure to lock the fastening screws

- v -

Image 7

Tandberg Data Tandberg LTO2 manual Do not cover the air inlet, Do not lift the device alone

Contents

Tandberg LTO2 Autoloader Trademarks FCC Class B Notice Description example in this manual Safety Descriptions Mandatory action Prohibited action General Cautions Safety Cautions Do not apply starburst wiring Do not lift the device alone Do not cover the air inlet Do not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Troubleshooting Chapter Daily MaintenanceChapter Cartridges Introduction Organization of this manual Symbols used in this manual Symbols used in this manualTip Overview of the Tandberg LTO2 Autoloader Tandberg LTO2 Autoloader Front Panel of the Tandberg LTO2 Autoloader Names and Functions of the Parts ･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display LCD Liquid Crystal Display Cartridges Handling PrecautionsTransfer or Disposal of the Device Main Unit Contents of the Carton Preparation Before Use SetupTransporter Locking Screw Instruction TAG Storing the Transporter Locking Screw for later use Scsi Cable Connections AC Power Cable Connection AC Power Cable Connection Attaching and removing a Filter Element Attaching and removing the Filter Element Scsi ID Setting Switching on the Power Switch and the Power-On Sequence Start and Shutdown of the System Removal of the Magazine Operation Loading the Magazine Loading the Magazine Loading to Magazine Loading the Cartridge Loading to the Fixed Slots For using the Tandberg LTO2 Autoloader w/BCRs optionalOperation Examples For using the Tandberg LTO2 Autoloader w/BCR Removal from and Insertion to the Magazine Removal and Insertion of the Cartridges Display Eject Slot? Removal from and Insertion to the Fixed Slots Slot Logical Numbers Organization of the Front Panel SwitchesFunctions of the Switches Operation of the Panel Keys Panel Operation Procedure Display Frm Slt 1? Menu Tree 1 Main Menu Menu Commands Retry Mode Checking the Scsi ID Setting the Scsi ID Operation Example Changing the Scsi ID Tip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release Key Cartridges Cartridges Data Cartridge Cleaning Cartridge Setting the Write-protect Switch Write-Protect Switch Bar Code Label Using Bar Code Labels Precautions General Precautions Usage Precautions Standards for Prohibition of Use Service LifeStorage of Data Cartridges Cleaning Daily MaintenanceCleaning of the Drive Head Manually Cleaning of the Drive Head Default CLNROL-function setting Enable Cleaning the Roller inside of the transporterChecking the CLNROL- function Setting the CLNROL- function Disable RtyCnt value in the CLNROL-function Changing the RtyCnt valueOperation Example Tip Execution timing of the cleaning Cleaning of the Roller Tools and Parts Setting Maintenance mode Cleaning the Roller Setting Cleaning mode Shows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the interior Cleaning of the Main UnitCleaning of the exterior Cleaning of the fixed slots Cleaning of the cartridge Cleaning of the magazine Movement and Shipping of the Autoloader Phenomenon Recovery Procedure Power Supply Troubleshooting Connections Phenomenon Recovery Procedure Cartridge Operation Cleaning Phenomenon Recovery Procedure Autoloader PerformanceOthers Recovery Procedure P move system initialization Exceeding the recommended operation Other Matters to Check When Requesting Maintenance Autoloader Main Unit Appendix a Specifications LTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Universal cleaning cartridge TD P/N Optional Items Appendix B Optional Items and SuppliesSupplies CMer Error Code Appendix C Error Code Err ×××× Messages Related to the Drive Interface Messages Message Description Panel Operation and Other Messages Tandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway Tandberg LTO2 Autoloader Installation and User’s Manual