Messages | Tandberg Data Tandberg LTO2 specs

Messages

Messages such as the following are displayed as required.

Messages Related to the Drive Interface

		Table-D6	Table of Messages Related to the Drive Interface

	Message		Description

	Drive status

	Calibrate	The drive is being calibrated.

	Cleaning	The drive is being cleaned.

	Erasing	The drive is erasing.

	Loading	The drive is loading.

	Locating	The drive is locating.

	Reading	The drive is reading.

	Rewinding	The drive is rewinding.

	REQ clean	The drive is requesting a cleaning.

	Unloading	The drive is unloading.

	Wait load	Waiting for loading completion following execution of the Load command.

	Wait unload	Waiting for unloading completion following execution of the Unload command.

	Writing	The drive is writing.

	DRV full	There is a cartridge in the drive.

	DRV empty	There isn't a cartridge in the drive.

	Autoloader and Drive

	COMM.ERROR	The Autoloader detected a communication error with the drive.

	Drive error and caution

	DRV Err 1	There has been detection of the drive exceeding the recommended operation temperature.

	DRV Err 2	There has been detection of the drive input voltage reaching the limit of or exceeding the
	DRV Err 2	permissible range.
		permissible range.
	DRV Err 3	A drive firmware error has occurred.

	DRV Err 4	A fault has occurred in the drive firmware or hardware.

	DRV Err 5	A fault has occurred in the drive hardware.

	DRV Err 6	A drive hardware or a media error has occurred.

	DRV Err 7	A fault of the media has occurred.

	DRV Err 8	An error has occurred in the drive hardware or SCSI bus.

	DRV Err 9	An error has occurred in the drive hardware or RS-422 connection.

	DRV Err A	An error has occurred in the drive hardware.

- 67 -

Image 83

Tandberg Data Tandberg LTO2 manual Messages Related to the Drive Interface

Contents

Tandberg LTO2 Autoloader Trademarks FCC Class B Notice Description example in this manual Safety Descriptions Mandatory action Prohibited action General Cautions Safety Cautions Do not apply starburst wiring Do not lift the device alone Do not cover the air inlet Do not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Cartridges Chapter Daily MaintenanceChapter Troubleshooting Introduction Organization of this manual Tip Symbols used in this manualSymbols used in this manual Overview of the Tandberg LTO2 Autoloader Tandberg LTO2 Autoloader Front Panel of the Tandberg LTO2 Autoloader Names and Functions of the Parts ･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display LCD Liquid Crystal Display Cartridges Handling PrecautionsTransfer or Disposal of the Device Main Unit Contents of the Carton Transporter Locking Screw Instruction TAG SetupPreparation Before Use Storing the Transporter Locking Screw for later use Scsi Cable Connections AC Power Cable Connection AC Power Cable Connection Attaching and removing a Filter Element Attaching and removing the Filter Element Scsi ID Setting Switching on the Power Switch and the Power-On Sequence Start and Shutdown of the System Removal of the Magazine Operation Loading the Magazine Loading the Magazine Loading to Magazine Loading the Cartridge Operation Examples For using the Tandberg LTO2 Autoloader w/BCRs optionalLoading to the Fixed Slots For using the Tandberg LTO2 Autoloader w/BCR Removal from and Insertion to the Magazine Removal and Insertion of the Cartridges Display Eject Slot? Removal from and Insertion to the Fixed Slots Slot Logical Numbers Organization of the Front Panel SwitchesFunctions of the Switches Operation of the Panel Keys Panel Operation Procedure Display Frm Slt 1? Menu Tree 1 Main Menu Menu Commands Retry Mode Checking the Scsi ID Setting the Scsi ID Operation Example Changing the Scsi ID Tip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release Key Cartridges Cartridges Data Cartridge Cleaning Cartridge Setting the Write-protect Switch Write-Protect Switch Bar Code Label Using Bar Code Labels Precautions General Precautions Usage Precautions Storage of Data Cartridges Service LifeStandards for Prohibition of Use Cleaning of the Drive Head Daily MaintenanceCleaning Manually Cleaning of the Drive Head Checking the CLNROL- function Cleaning the Roller inside of the transporterDefault CLNROL-function setting Enable Setting the CLNROL- function Disable Operation Example Changing the RtyCnt valueRtyCnt value in the CLNROL-function Tip Execution timing of the cleaning Cleaning of the Roller Tools and Parts Setting Maintenance mode Cleaning the Roller Setting Cleaning mode Shows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the interior Cleaning of the Main UnitCleaning of the exterior Cleaning of the fixed slots Cleaning of the cartridge Cleaning of the magazine Movement and Shipping of the Autoloader Phenomenon Recovery Procedure Power Supply Troubleshooting Connections Phenomenon Recovery Procedure Cartridge Operation Others Phenomenon Recovery Procedure Autoloader PerformanceCleaning Recovery Procedure P move system initialization Exceeding the recommended operation Other Matters to Check When Requesting Maintenance Autoloader Main Unit Appendix a Specifications LTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Universal cleaning cartridge TD P/N Supplies Appendix B Optional Items and SuppliesOptional Items CMer Error Code Appendix C Error Code Err ×××× Messages Related to the Drive Interface Messages Message Description Panel Operation and Other Messages Tandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway Tandberg LTO2 Autoloader Installation and User’s Manual