Cleaning, Others | Tandberg Data Tandberg LTO2 specification

	Phenomenon	Recovery Procedure

	Autoloader Performance

	Data backup efficiency of the	Check whether the Autoloader drive is connected to an exclusive SCSI
	Data backup efficiency of the	device and whether it is part of a daisy chain connection with another tape
	Autoloader is poor.
	Autoloader is poor.	drive or hard drive.
		drive or hard drive.

	Operation

		･Check the access rights of the host device against the file system.
	Cannot write to data cartridge.	･Check whether the data cartridge being used is the proper type.
	Cannot write to data cartridge.	･Check the write protect tab of the tape and ascertain whether the tape is in
		a condition that can accept writing.
		･Replace with a new data cartridge.

	Cleaning

	The cleaning message is	･Replace the current cleaning cartridge with a new one.
	The cleaning message is	･When a message to the effect that cleaning is required appears on the
	displayed repeatedly.
	displayed repeatedly.	LCD even after cleaning of the drive, replace the cleaning cartridge.


	Alarm LED is brinking.
	“REQ CLNROL” message is	･Execute cleaning of the Roller.See”Section 5.1.2”
	displayed repeatedlly.

	Others

		･Check the setting of the application software(change setting ,
		removing the cartridge after backup job).
	The cartridge remains in the	･Eject from operation panel.
	drive.	･Execute cleaning of the Roller.See”Section 5.1.2”
		･If the phenomenon has a relapse,contact your nearest Customer Support
		Center.

- 56 -

Image 72

Tandberg Data Tandberg LTO2 manual Phenomenon Recovery Procedure Autoloader Performance, Cleaning, Others

Contents

Tandberg LTO2 Autoloader FCC Class B Notice Trademarks Safety Descriptions Description example in this manual Prohibited action Mandatory action Safety Cautions General Cautions Do not apply starburst wiring Do not cover the air inlet Do not lift the device alone Do not disassemble, repair or modify by yourself Vii Figure Ⅰ Warning Label ① Revision History Contents Chapter Daily Maintenance Chapter TroubleshootingChapter Cartridges Introduction Organization of this manual Symbols used in this manual Symbols used in this manualTip Tandberg LTO2 Autoloader Overview of the Tandberg LTO2 Autoloader Names and Functions of the Parts Front Panel of the Tandberg LTO2 Autoloader ･ Enter key Rear Panel of the Tandberg LTO2 Autoloader Liquid Crystal Display Liquid Crystal Display LCD Handling Precautions Transfer or Disposal of the DeviceMain Unit Cartridges Contents of the Carton Setup Preparation Before UseTransporter Locking Screw Instruction TAG Scsi Cable Connections Storing the Transporter Locking Screw for later use AC Power Cable Connection AC Power Cable Connection Attaching and removing the Filter Element Attaching and removing a Filter Element Switching on the Power Switch and the Power-On Sequence Scsi ID Setting Start and Shutdown of the System Operation Removal of the Magazine Loading the Magazine Loading the Magazine Loading the Cartridge Loading to Magazine For using the Tandberg LTO2 Autoloader w/BCRs optional Loading to the Fixed SlotsOperation Examples For using the Tandberg LTO2 Autoloader w/BCR Removal and Insertion of the Cartridges Removal from and Insertion to the Magazine Removal from and Insertion to the Fixed Slots Display Eject Slot? Organization of the Front Panel Switches Functions of the SwitchesOperation of the Panel Keys Slot Logical Numbers Panel Operation Procedure Display Frm Slt 1? Menu Commands Menu Tree 1 Main Menu Retry Mode Setting the Scsi ID Checking the Scsi ID Changing the Scsi ID Operation Example Tip Display Drv. ID 0? Using the Emergency Release Key Using the Emergency Release Key Cartridges Cartridges Cleaning Cartridge Data Cartridge Write-Protect Switch Setting the Write-protect Switch Using Bar Code Labels Precautions Bar Code Label Usage Precautions General Precautions Service Life Standards for Prohibition of UseStorage of Data Cartridges Daily Maintenance CleaningCleaning of the Drive Head Manually Cleaning of the Drive Head Cleaning the Roller inside of the transporter Default CLNROL-function setting EnableChecking the CLNROL- function Setting the CLNROL- function Disable Changing the RtyCnt value RtyCnt value in the CLNROL-functionOperation Example Tip Cleaning of the Roller Execution timing of the cleaning Tools and Parts Setting Maintenance mode Setting Cleaning mode Cleaning the Roller Shows the upper Roller after cleaning Tip 12 shows the upper Roller after cleaning Operation Cleaning of the Main Unit Cleaning of the exteriorCleaning of the fixed slots Cleaning of the interior Cleaning of the magazine Cleaning of the cartridge Movement and Shipping of the Autoloader Troubleshooting Phenomenon Recovery Procedure Power Supply Phenomenon Recovery Procedure Cartridge Operation Connections Phenomenon Recovery Procedure Autoloader Performance CleaningOthers Recovery Procedure P move system initialization Exceeding the recommended operation When Requesting Maintenance Other Matters to Check Appendix a Specifications Autoloader Main Unit Universal cleaning cartridge TD P/N LTO2 Data Cartridge TD P/N LTO1 Data Cartridge TD P/N Appendix B Optional Items and Supplies Optional ItemsSupplies Appendix C Error Code CMer Error Code Err ×××× Messages Messages Related to the Drive Interface Panel Operation and Other Messages Message Description Tandberg LTO2 Autoloader Installation and User’s Manual Tandberg Data ASA Kjelsasveien 161 N-411 Oslo Norway