A4.7 Additional Information | Toshiba B-852-TS12-QQ instruction

APPENDIX 4 SYSTEM MODE

EO1-33029

A4.7 Additional Information

A4.7 Additional Information

A4.7.1 Self-Diagnostic Test Result Sample and Descriptions

∙Print Sample

(1)	PROGRAM	B-850	01NOV2000
		V1.0A	FMRM0051402: 1A00
(2)	BOOT	B-850	16NOV2000
		V1.0	FMRM0051601:8500
(3)	FONT	5600
(4)	KANJI	8900
(5)	EEPROM	OK
(6)	SDRAM	8MB
(7)	CARD	SLOT1	ATA
		SLOT2	LAN
(8)	SENSOR1	00000000, 00000000
(9)	SENSOR2	[H]20°C [A]22°C [S]25°C
		[R(U)]4.2V [R(L)]4.0V
		[T]2.5V
(10)	EXP.I/O	NG
(11)	KEY BRD	NG

NOTES:

1.Print conditions:

Preset count: 1, Print speed: 4”/sec., Sensor: No sensor, Printing method: Thermal transfer,

Supply length: 78 mm, Issue mode: Batch printing

2.Software version No., Part No. of ROM and checksum will vary according to the software version of

PROGRAM ROM.

3.The last two digits of the checksum are usually “00”.

4.When Kanji ROM is not installed, the checksum becomes “0000”.

5.The symbol”°” of ‘°C” may not be printed depending on the type of character code.

∙Descriptions

(1)Program ROM Check (Model Name, Date, Version, Part number, Checksum)

PROGRAM B-850

01NOV2000

Program area

V1.0

A

FMRM0051402:

1A00

Checksum

Model name

Part No. of ROM or software

Software version No.

Revision No.: Space or A to Z

(2) Boot Check (Model Name, Date, Version, Part Number, Checksum)

BOOT B-850

16NOV2000

Boot area

V1.0

A

FMRM0051601:

8500

Checksum of Boot area

Model name

Part No. of ROM or software

Software version No.

Revision No.: Space or A to Z

A4-23

Image 101

Toshiba B-852-TS12-QQ owner manual A4.7 Additional Information, A4.7.1 Self-Diagnostic Test Result Sample and Descriptions

Contents

852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents A2-1 A1-1A3-1 A4-1 Unpacking Introduction FeaturesProduct Overview Accessories Front View Rear View DimensionsAppearance Interior Operation Panel Precautions Printer Setup Procedure before Operation Assembling the Supply Holder Frame Assembling the Accessories Connecting the Cables to Your Printer Connecting the Power Cord Turning OFF the Printer Turning the PrinterTurning on the Printer Disassembling the Supply Holder Unit Installing the Media onto the Supply Holder Unit Installing the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Below Printer Setting the Black Mark Sensor Setting Sensor PositionsSetting the Feed Gap Sensor Loading the Ribbon COM Inserting the Optional Pcmcia Cards Test Print At the same time Test Print Overview Operating Modes Printer Operation Operating Modes System Requirements Installing the Printer DriversDriver Download System EO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Print to the following Details Tab Print using ∙ Click Capture Printer Port Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Stock Tab Stock Tab Sensor Select Stock Tab Options tab, the following display screen will appear Options Tab Testing Tab Testing Tab Testing Tab Testing Tab About Tab About Tab Operation Panel On Line Mode Operation Reset Restart key Dump Mode Receive buffer size Print Conditions Print Head/Platen/ Sensors MaintenanceCleaning Care/Handling of the Media and Ribbon Error Messages Problems/Causes Solutions TroubleshootingError Messages Possible Problems Causes Solutions Possible ProblemsError Messages Problems/Cause Solutions Removing Jammed Media Feed key Threshold Setting„Threshold setting procedure Model 852-TS12-QQ Appendix 1 SpecificationsA1.1 Printer A1.3 Media A1.2 OptionsA1.3.1 Media Type Label A1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective Sensor A1.4 Ribbon Appendix 2 Messages and Leds Symbols in the message Following message appears „Interface Cables Appendix 3 Interface A4.1 Operation Panel Appendix 4 System Mode A4.2 Overview If the power is turn on while Maintenance counter/parameter settings print out A4.3 Self-Diagnostic TestPrinting mode selection Print head element check Self-Diagnostic Test and the result print out A4.4 Printer Parameter Fine Adjustment Restart Feed Feed Length Fine Adjustment Cut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Rewind Motor Feed Motor Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor A4.4 Printer Parameter Fine Adjustment ContBlack Mark Sensor Feed Gap Sensor Test Pattern Selection Print Condition SettingA4.5 Test Print Specifying the Print Condition for the Test Print Issue Count Setting Sensor Type Selection Print Speed SettingPrinting Mode Selection Paper Feed Selection Issue Mode SelectionLabel Length Setting Pause key Test Print Pattern SelectionSlant Line 1 dot Slant Line 3 dots Barcode CharactersNon-Printing Factory Test Auto Print A4.6 PCL Emulation Setting Sensor Type Selection Emulation ON/OFF SelectionPrint Speed Media Size Selection Issue Mode SelectionMedia Width Setting Media Length Setting A4.7 Additional Information A4.7.1 Self-Diagnostic Test Result Sample and Descriptions Sdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD Letter A4.7.3 Magnified Views of Slant Line Pattern Appendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full Ascii KIX Code MaxiCode UPC-A+2 digits UPC-A+5 digits Bar code Glossaries Pre-printed media Index Index Page