Total Feed | Toshiba B-852-TS12-QQ manual

APPENDIX 4 SYSTEM MODE

EO1-33029

A4.7 Additional Information

A4.7.2 Maintenance Counter/Parameter Check Print Sample and Descriptions

∙Print Sample

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

(14)

(15)

(16)

(17)

(18)

(19)

(20)

(21)

(22)

(23)

(24)

(25)

(26)

(27)

(28)

(29)

(30)

(31)

(32)

(33)

(34)

(35)

(36)

(37)

(38)

(39)

(40)

(41)

(42)

(43)

(44)

(45)

(46)

(47)

(48)

(49)

TOTAL FEED	1.1Km
FEED	1.1Km
PRINT	0.5Km
CUT	96
RIBBON	3H
232C ERR	255
SYSTEM ERR	0
POWER FAIL	0

[PC]		[KEY]
FEED	+2.0mm	FEED	+0.0mm
CUT	+0.0mm	CUT	+1.0mm
BACK	+0.0mm	BACK	+0.0mm
TONE(T)	+0 step	TONE(T)	+0 step
TONE (D)	+0 step	TONE(D)	+0 step
RBN(FW)	-10	RBN (FW)	-8
RBN (BK)	+0	RBN (BK)	+0
X ADJ.	+0.0mm
THRESHOLD (R)		1.0V
THRESHOLD (T)		0.7V
FONT		[PC-850] [0]
CODE		[AUTO]
SPEED		[9600]
DATA LENG.		[8]
PARITY		[EVEN]
CONTROL		[XON+READY AUTO]
MESSAGE		[ENGLISH]
FORWARD WAIT		[ON]+0.0mm
FEED KEY		[FEED]
KANJI		[TYPE1]
EURO CODE		[B0]
AUTO HD CHK		[OFF]
WEB PRINTER		[OFF]
SILENT PRINT		[ON]
KB80 CONNECT		[OFF]
PRTR IP ADDR		[192.168.010.020]
GATE IP ADDR		[000.000.000.000]
SUBNET MASK		[255.255.255.000]
TTF AREA		[704KB]
EXT CHR AREA		[128KB]
BASIC AREA		[64KB]
PC SAVE AREA		[64KB]
PCL EMULATION		[ON]
PRINT SPEED		[4”/S]
SENSOR		[TRANS.]
PRINT TYPE		[TRANSFER]
TYPE		[NO CUT]
MEDIA		[USER 2169X0742]
SOCKET PORT		[OFF][08000]
BASIC		[OFF]
BASIC TRACE		[OFF]

NOTE:

Print conditions:

Preset count: 1, Print speed: 4”/sec., Sensor: No sensor, Printing mode: Thermal transfer, Media

length: 170 mm, Issue mode: Batch printing

A4-27

Image 105

Toshiba B-852-TS12-QQ owner manual Total Feed

Contents

852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents A2-1 A1-1A3-1 A4-1 Introduction Features Product OverviewUnpacking Accessories Dimensions AppearanceFront View Rear View Interior Operation Panel Precautions Printer Setup Procedure before Operation Assembling the Supply Holder Frame Assembling the Accessories Connecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Disassembling the Supply Holder Unit Installing the Media onto the Supply Holder Unit Installing the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Below Printer Setting Sensor Positions Setting the Feed Gap SensorSetting the Black Mark Sensor Loading the Ribbon COM Inserting the Optional Pcmcia Cards Test Print At the same time Test Print Overview Operating Modes Printer Operation Operating Modes System Requirements Installing the Printer DriversDriver Download System EO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Print to the following Details Tab Print using ∙ Click Capture Printer Port Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Stock Tab Stock Tab Sensor Select Stock Tab Options tab, the following display screen will appear Options Tab Testing Tab Testing Tab Testing Tab Testing Tab About Tab About Tab Operation Panel On Line Mode Operation Reset Restart key Dump Mode Receive buffer size Print Conditions Maintenance CleaningPrint Head/Platen/ Sensors Care/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Possible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Removing Jammed Media Threshold Setting „Threshold setting procedureFeed key Appendix 1 Specifications A1.1 PrinterModel 852-TS12-QQ A1.3 Media A1.2 OptionsA1.3.1 Media Type Label A1.3.2 Detection Area of the Transmissive Sensor A1.3.4 Effective Print Area A1.3.3 Detection Area of the Reflective Sensor A1.4 Ribbon Appendix 2 Messages and Leds Symbols in the message Following message appears „Interface Cables Appendix 3 Interface A4.1 Operation Panel Appendix 4 System Mode A4.2 Overview If the power is turn on while A4.3 Self-Diagnostic Test Printing mode selectionMaintenance counter/parameter settings print out Print head element check Self-Diagnostic Test and the result print out A4.4 Printer Parameter Fine Adjustment Restart Feed Feed Length Fine Adjustment Cut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Rewind Motor Feed Motor Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Threshold Manual Fine Adjustment Black Mark/Feed Gap Sensor A4.4 Printer Parameter Fine Adjustment ContBlack Mark Sensor Feed Gap Sensor Print Condition Setting A4.5 Test PrintTest Pattern Selection Specifying the Print Condition for the Test Print Issue Count Setting Print Speed Setting Printing Mode SelectionSensor Type Selection Issue Mode Selection Label Length SettingPaper Feed Selection Pause key Test Print Pattern SelectionSlant Line 1 dot Slant Line 3 dots Barcode CharactersNon-Printing Factory Test Auto Print A4.6 PCL Emulation Setting Emulation ON/OFF Selection Print SpeedSensor Type Selection Issue Mode Selection Media Width SettingMedia Size Selection Media Length Setting A4.7 Additional Information A4.7.1 Self-Diagnostic Test Result Sample and Descriptions Sdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD Letter A4.7.3 Magnified Views of Slant Line Pattern Appendix 5 Print Samples UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits CODE39 Full Ascii KIX Code MaxiCode UPC-A+2 digits UPC-A+5 digits Bar code Glossaries Pre-printed media Index Index Page