Appendix 3 Interface, „Interface Cables | Toshiba B-852-TS12-QQ

APPENDIX 3 INTERFACE

EO1-33029

APPENDIX 3 INTERFACE

APPENDIX 3 INTERFACE

„Interface Cables

To prevent radiation and reception of electrical noise, the interface cables must meet the following requirements:

∙Fully shielded and fitted with metal or metallized connector housings.

∙Keep as short as possible.

∙Should not be bundled tightly with power cords.

∙Should not be tied to power line conduits.

„RS-232C Cable description

The serial data cable used to connect the printer to the host computer should be one of the following two types:

DB-9S											DB-9P
Connector to PC											Connector to Printer
Pin No.	Signal										Pin No.		Signal
1	N.C.									1			N.C.
2	RXD									2			TXD
2	RXD									2			TXD
3	TXD									3			RXD
3	TXD									3			RXD
4	DTR									4			DSR
4	DTR									4			DSR
5	GND									5			SG
5	GND									5			SG
6	DSR									6			DTR
6	DSR									6			DTR
7	RTS									7			CTS
7	RTS									7			CTS
8	CTS									8			RTS
8	CTS									8			RTS
9	N.C.									9			N.C.
Housing	Shield										Housing		Shield
Housing	Shield										Housing		Shield
DB-25S											DB-9P
Connector to PC											Connector to Printer
Pin No.	Signal										Pin No.		Signal
1	Shield										1		N.C.
1	Shield										1		N.C.
2	TXD										2		TXD
3	RXD										3		RXD
4	RTS										4		DSR
5	CTS										5		SG
6	DSR										6		DTR
6	DSR										6		DTR
7	GND										7		CTS
20	DTR										8		RTS
20	DTR										8		RTS
											9		N.C.

NOTE:

Use an RS-232C cable with inch type securing screws on the connector.

A3-1

Image 78

Toshiba B-852-TS12-QQ owner manual Appendix 3 Interface, „Interface Cables

Contents

852-TS12-QQ Energy Star is a U.S. registered mark $51,1 3UHFDXWLRQV Table of Contents A3-1 A1-1A2-1 A4-1 Introduction Features Product OverviewUnpacking Accessories Dimensions AppearanceFront View Rear View Operation Panel Interior Printer Setup Precautions Procedure before Operation Assembling the Accessories Assembling the Supply Holder Frame Connecting the Cables to Your Printer Connecting the Power Cord Turning the Printer Turning on the PrinterTurning OFF the Printer Installing the Media onto the Supply Holder Unit Disassembling the Supply Holder Unit Installing the Media and reassembling the Supply Holder Unit Loading Media into the Printer Print Head Block Element Release Lever Printer Below Setting Sensor Positions Setting the Feed Gap SensorSetting the Black Mark Sensor Loading the Ribbon Inserting the Optional Pcmcia Cards COM Test Print At the same time Test Print Printer Operation Overview Operating Modes Operating Modes Driver Download Installing the Printer DriversSystem Requirements System EO1-33029 Installing the Printer Drivers Driver Download Driver Installation Cont Driver Installation Add Printers Add Printers Uninstalling the TEC B-852 Printer Driver Using the B-852 Printer Properties Menus Printer Operation General Properties Tab Details Tab Print to the following Print using ∙ Click Capture Printer Port Regional Settings Tab Regional Settings Tab Setup Tab Portrait Landscape Rotated Additional Advanced Options Graphics Tab Bar Fonts Tab Printer Operation Bar Fonts Tab Stock Tab Stock Tab Sensor Select Stock Tab Options Tab Options tab, the following display screen will appear Testing Tab Testing Tab Testing Tab Testing Tab About Tab About Tab On Line Mode Operation Panel Operation Reset Dump Mode Restart key Print Conditions Receive buffer size Maintenance CleaningPrint Head/Platen/ Sensors Care/Handling of the Media and Ribbon Troubleshooting Error MessagesError Messages Problems/Causes Solutions Possible Problems Error Messages Problems/Cause SolutionsPossible Problems Causes Solutions Removing Jammed Media Threshold Setting „Threshold setting procedureFeed key Appendix 1 Specifications A1.1 PrinterModel 852-TS12-QQ A1.3.1 Media Type A1.2 OptionsA1.3 Media Label A1.3.2 Detection Area of the Transmissive Sensor A1.3.3 Detection Area of the Reflective Sensor A1.3.4 Effective Print Area A1.4 Ribbon Symbols in the message Appendix 2 Messages and Leds Following message appears Appendix 3 Interface „Interface Cables Appendix 4 System Mode A4.1 Operation Panel If the power is turn on while A4.2 Overview A4.3 Self-Diagnostic Test Printing mode selectionMaintenance counter/parameter settings print out Self-Diagnostic Test and the result print out Print head element check A4.4 Printer Parameter Fine Adjustment Feed Length Fine Adjustment Restart Feed Cut Position Fine Adjustment Back Feed Length Fine Adjustment Axis Fine Adjustment Thermal Transfer Print Thermal Direct Print Ribbon Motor Voltage Fine Adjustment Feed/Rewind Motor Rewind Motor Feed Motor Black Mark Sensor A4.4 Printer Parameter Fine Adjustment ContThreshold Manual Fine Adjustment Black Mark/Feed Gap Sensor Feed Gap Sensor Print Condition Setting A4.5 Test PrintTest Pattern Selection Issue Count Setting Specifying the Print Condition for the Test Print Print Speed Setting Printing Mode SelectionSensor Type Selection Issue Mode Selection Label Length SettingPaper Feed Selection Slant Line 1 dot Test Print Pattern SelectionPause key Slant Line 3 dots Non-Printing CharactersBarcode Factory Test A4.6 PCL Emulation Setting Auto Print Emulation ON/OFF Selection Print SpeedSensor Type Selection Issue Mode Selection Media Width SettingMedia Size Selection Media Length Setting A4.7.1 Self-Diagnostic Test Result Sample and Descriptions A4.7 Additional Information Sdram 8MB SENSOR1 0 0 0 0 0 0 0 0 1 0 0 1 EXP.I/O OK Total Feed ∙ Descriptions of the Maintenance Counter ODD ODD A4.7.3 Magnified Views of Slant Line Pattern Letter Appendix 5 Print Samples CODE39 Full Ascii UPC-E+2 digits UPC-E+5 digits EAN8+2 digits EAN8+5 digits UPC-A+2 digits UPC-A+5 digits KIX Code MaxiCode Glossaries Bar code Pre-printed media Index Index Page