Automatic Calibration, Auto Calib | Toshiba B-EX4T1 manual

2.6.6 Automatic Calibration

2. PRINTER SETUP

ENGLISH VERSION EO1-33089

2.6 Printer Setting

2.6.6 Automatic Calibration

USER SYSTEM MODE

<4>LAN/WLAN

<5>BASIC

<6>Z-MODE

<7>AUTO CALIB

The Auto Calibration menu allows selecting whether or not to enable the automatic calibration at a power on time. When the automatic calibration is activate, the printer feeds the media for about 160 mm each time the power is turned on or the top cover is opened, to detect a print start position.

(1) AUTO CALIB
•	OFF	Disabled.
•	ON TRANS.	Enabled. (Transmissive sensor)
•	ON REFLECT	Enabled. (Reflective sensor)
•	ON ALL	Enabled. (Transmissive & Reflective
		sensors)
•	ON TRANS.+Bfeed	Auto calibration + back feed
		(Transmissive sensor)
•	ON REFLECT+Bfeed	Auto calibration + back feed
		(Reflective sensor)
•	ON ALL+Bfeed	Auto calibration + back feed
		(Transmissive & Reflective sensors)

NOTES:

1.When AUTO CALIB is enabled, an automatic calibration is performed at an open/close of the print head and at a power on time.

2.When AUTO CALIB is enabled, the media length, effective print length, sensor type, and whether to use ribbon or not specified by commands are ignored.

3.This function is available only when the media pitch is 10.0 mm to 150.0 mm.

4.When the printer cannot detect the second black mark/gap, it will continue to feed the media for up to 500.0mm. If this does not work, the printer will stop, resulting in a paper jam.

5.During an automatic calibration, the printer also feeds the ribbon. Even if the ribbon is not loaded, no error results. However, the print condition will be automatically changed to “No ribbon” after the calibration ends.

6.When the cutter is installed and a previous issue was performed in cut issue mode, the media is cut and ejected after an automatic calibration completes.

7.When a label end or a head open occurs during an automatic calibration, the printer stops, resulting in an error. Loading new media and closing the print head can clear the error and resume the automatic calibration.

8.The media is fed backward after an auto calibration is performed if the reverse feed is enabled.

E2-26

Image 40

Toshiba B-EX4T1 manual Automatic Calibration, Auto Calib

Contents

B-EX4T1 SERIES TOSHIBA Barcode Printer N258 IP20CE Compliance for EU only VORSICHT Owners Manual Waste Recycling information for users For safety For EuropeFor USA For Canada Safety Summary Meanings of Each Symbol Precautions Request Regarding Maintenanceand cause fire or electric shock Fire or electric shock could PRINTER SETUP TABLE OF CONTENTSPRODUCT OVERVIEW ON LINE MODE 1.2 Features 1. PRODUCT OVERVIEW1.1 Introduction 1.3 Unpacking … Power cord 1.4 AccessoriesENGLISH VERSION EO1-33089 1.4 Accessories Dimensions Appearance1.5.1 1.5.2 Front View 1.5.4 Operation Panel 1.5.5 Interior 1.6 Options Option NameType Description 2. PRINTER SETUP Setup FlowProcedure Reference 2.1 Installation 2.2 Connecting the Power Cord Example of US Type 2.3 Loading Supplies ENGLISH VERSION EO1-33089 2.3 Loading Supplies 2.3.1 Loading the Media 2.3.1 Loading the Media Cont Setting the Feed Gap Sensor position Setting the Black Mark Sensor position STANDARD/PEEL OFF position 14. Loading with cutter 2.3.2 Loading the Ribbon Ribbon path 2.3.2 Loading the Ribbon Cont Auto Ribbon Saving Mode 2.4 Connecting the Cables to Your Printer 2.5 Turning the Printer ON/OFF 2.5.1 Turning ON the Printer 2.6 Printer Setting Power OFFONLINE Mode PAUSE state Cont 2.6.1 User System ModeFunction 9LOG ⇒ Section 2.6.2 Parameter Setting Contents of the Parameter Set MenuMenu Sub menu Cont 2.6.2.1 Printer Set 2.6.2 Parameter Setting Cont 2.6.2.2 Software Set This parameter is to choose the function of the FEED key This parameter is to choose a Maxicode specification 16 XML 17 THRESHOLD SELECT18 ENERGY TYPE 19 PW SAVE TIME 2.6.2.3 PANEL 2.6.4 Basic Program Setting 2.6.2 Parameter Setting Cont 2.6.3 Enabling LAN/WLAN2.6.2.4 PASSWORD 2.6.4 Basic Program Setting Cont 2.6.5 Enabling Z-Mode 3 TRACE4 EXPAND MODE 1 Z-MODE 2.6.6 Automatic Calibration 1 AUTO CALIB 1 BUFFER 2.6.7 Dump Mode Setting2 DUMP LIST 2.6.7 Dump Mode Setting Cont The data in the receive buffer is printed as followsReceive Buffer Size Required Media Length The Log menu allows saving print logs in a USB memory 2.6.8 Logging1 LOG The System Mode consists of the following menus 2.6.9 System Mode11RTC ⇒ Section 2.6.10 Interface Setting Contents of the Interface Menu 3 BASIC INFORMATION 5 GATEWAY ADDRESS6 SUBNET MASK 7 SOCKET PORT 8 PORT NUMBER 9 DHCP10 DHCP CLIENT ID 11 DHCP HOST NAME 2.6.10 Interface Setting Cont 13 WLAN MODE 14 DEFAULT KEY 15 802.11b CHANNEL16 802.11b BAUD 17 802.11g CHANNEL 19 WLAN POWER SAVE 20 WINS21 WINS ADDRESS 1 USB SERIAL ID 2 DATA LENGTH 3 STOP BIT4 PARITY 5 CONTROL This parameter is to set date and time 2.6.12 Copying Data to/from USB Memory 2.7 Installing the Printer Drivers 2.7.3 Installing the Printer Driver2.7.1 Introduction 2.7.2 General Description 2.7.4 Preparation for Installation 5 When the installation is completed, click the Finish button E2-42 2.7.5 Installation under Windows 2000/XP/Server2003 6 Specify a printer port and click the Next button 9 The list of the installable printer is displayed E2-46 17 Installation of the printer driver starts 2.7.6 Installation under Windows Vista/Server2008/7/Server2008R2 E2-48 E2-49 11 Installation starts 2.7.7 Installation under Windows 2000 USB with Plug & Play Enabled E2-51 9 When the screen on the right is displayed, click the Yes button E2-53 E2-54 2.7.10 Uninstalling the Printer Driver 4 Click the Finish button to start to delete the printer drivers 2 To delete the V6.5 Build75 or V6.5 Build77 z Deleting the setup information configured during the preparationE2-57 2.8 Print Test Adjustment 2.8 Print Test Cont „ When using a Strip Module or an optional Cutter Module 2.9 Position and Print Tone Fine Adjustment 2.9.1 Fine AdjustmentFine adjustment ⇒Section Contents of the Fine Adjustment Menu 2.9.1 Fine AdjustmentCont Example of Cut Position Fine Adjustment Example of Peel-off Position Fine Adjustment2 CUT ADJ E2-62 Example of Reverse Feed Amount Fine Adjustment 3 BACK ADJ Example of X Coordinate Fine Adjustment 4 X ADJUSTE2-64 Print tone for the thermal transfer printing is fine adjusted 2.9.1 Fine Adjustment Cont 10 THRESHOLD TRANS8 RBN ADJ.BK 9 THRESHOLD REFL 2.10 Threshold Setting 2.10 Threshold Setting Cont 7 The result after manually setting the threshold is displayed5 Press the RIGHT to see the details e.g Succeeded Sensor adjustment 2.11 Sensor SettingContents of the Sensor Adjust Menu 2.11 Sensor Setting Cont 3 PE REFL./TRANS ON LINE MODE Key Functions Error state 3.2 LCDOnline state 3.3 Operation Example „ Online Mode 3.3 Operation Example Cont „ Help Guide Message „ Cancellation of Print Job 4.1 Cleaning 4. MAINTENANCE4.1.1 Print Head/Platen/ Sensors 4.1.1 Print Head/Platen/ Sensors Cont 4.1.2 Covers and Panels 4.1.3 Optional Cutter Module 5. TROUBLESHOOTING 5.1 Error Messages 5.1 Error Messages Cont 5.1 Error Messages Cont 5.2 Possible Problems ENGLISH VERSION EO1-33089 5.2 Possible Problems 5.3 Removing Jammed Media ENGLISH VERSION EO1-33089 5.3 Removing Jammed Media 6. PRINTER SPECIFICATIONS This section describes the printer specificationsModel B-EX4T-GS12-QM-R/CN-R Bar code types 7.1 Media 7. SUPPLY SPECIFICATIONS7.1.1 Media Type B-EX4T-TS12-QM-R Label 7.1.2 Detection Area of the Transmissive SensorTag paper with square holes 7.1.3 Detection Area of the Reflective Sensor 7.1.4 Effective Print Area 7.1.5 RFID Tags Cautions for using RFID Tags 7 Printing on Bump Chip/Antenna Area 7.3 Recommended Media and Ribbon Types 7.2 RibbonENGLISH VERSION EO1-33089 7.2 Ribbon 7.4 Care/Handling of Media and Ribbon 7.3 Recommended Media and Ribbon Types ContCombination of Media and Ribbon APPENDIX 1 MESSAGES AND LEDS Symbols in the messagePage Example ESCT20G30LF NUL Command error Example ESCPC0010A00,0300,2,2,A,00,BLFNUL Command errorExample USB interface Standard APPENDIX 2 INTERFACELAN Standard Serial interface Option B-EX700-RS-QM-R Parallel interface Centronics Option B-EX700-CEN-QM-R IEEE1284-B Connector USB Host interface Option B-EX700-RTC-QM-R Wireless LAN Option B-EX700-WLAN-QM-RShared key for WEP, PSK, PEAP, TLS, TTLS, MD5, LEAP, EAP-FAST Expansion I/O Interface Option B-EX700-IO-QM-R N.C. No Connection RFID Option B-EX700-RFID-U2-US-RB-EX700-RFID-U2-EU-R B-EX700-RFID-H1-QM-R APPENDIX 3 PRINT SAMPLES FontAPPENDIX 3 PRINT SAMPLES ENGLISH VERSION EO1-33089 APPENDIX 3 PRINT SAMPLES APPENDIX 3 PRINT SAMPLES Cont Bar codes UPC-A+5 digits GS1 DataBar Stacked GS1 DataBar LimitedUPC-A EAN-13 EAN-8 GS1 DataBar Expanded StackedUCC/EAN-128 with CC-A or CC-B APPENDIX 4 GLOSSARIES Printer IP address EO1-33089